manualshive.com logo in svg

Gude Expert Net Control 2304, Manual, Page: 8 / 87

Share
Download
Gude Expert Net Control 2304 Manual Download Page 8

8

Expert Net Control 2304 

 

                                                                                                                                                                                          © 2021 GUDE Systems GmbH

Device Description

12. AC mains power supply
13. 8x relay switching contacts (NO)

Commissioning

·

Connect the device to the mains (100-240V AC) or to a plug-in power supply (12V to
24V AC, 12V to 30V DC).

·

Plug the network cable into the Ethernet socket (RJ45). 

·

Connect the relays to the loads that are to be operated.

·

Establish contact between the lines to be monitored and the digital inputs.

·

Connect a sensor (if available).

1.4.1

Connection Example

Here is an example with block diagram in which the device is supplied with 230V AC
and in which eight AC loads (L1 - L8) are connected. In addition, the inputs are as-
signed eight switches (S1 - S8).

Summary of Contents for Expert Net Control 2304
























































































Reviews:

No comments