manualshive.com logo in svg

Gude Expert Net Control 2304, Manual, Page: 33 / 87

Share
Download
Gude Expert Net Control 2304 Manual Download Page 33

33

Expert Net Control 2304 

 

                                                                                                                                                                                          © 2021 GUDE Systems GmbH

Configuration

Telnet TCP port: Telnet sessions are accepted on this port.

Raw mode: The VT100 editing and the IAC protocol are disabled.

Activate echo: The echo setting if not changed by IAC.

Active negotiation: The IAC negotiation is initiated by the server.

Require user login: Username and password are required.

Delay after 3 failed logins: After 3 wrong entries of username or password, the next lo-
gin attempt is delayed.

Use radius server passwords: Username and password are validated by a Radius
Sever.

Use locally stored passwords: Username and password are stored locally

3.4.2

Syslog

Enable Syslog: Enables the usage of Syslog Messages.

Syslog Server:  If you have enabled Syslog Messages, enter the IP address of the
server to which the syslog information should be transmitted.

3.4.3

SNMP

Summary of Contents for Expert Net Control 2304
























































































Reviews:

No comments