background image

Guardian Telecom Inc. 

Installation and Operation 

WRR/WRT-VoIP Series Telephones 

Page 17

 

 

 

18.  Field Repairs 

Field repairs may only be carried out by qualified technicians using OEM parts.  Substitution of 
parts voids warranty and may pose a hazard to users of the equipment. 

See: 19 Replacement 
Parts 

Disconnect the telephone IP Cable and Aux Power if necessary. 

 

Carefully remove the front cover assembly and separate from the housing by disconnecting the 
harness plugs.  NOTE that the handset and all electronics are attached to the front plate. 

Perform the necessary repairs or adjustments. 

 

Carefully replace the front plate and install all screws.  Do not over tighten the cover screws. 
There is a flexible gasket between the cover and the body; excessive tightening of the screws 
deforms the gasket and reduces the weather resistance of the set. 

 

Handset Replacement 

 

Refer to the instruction sheet included with the replacement handset. 

 

Disconnect the handset wiring from the PCBA. 

 

If the phone is equipped with an armored cord handset, remove the anchor screw from the 
armored cord lanyard. 

 

Loosen the handset cable gland and pull out the cord. 

 

Install the new replacement handset and tighten the gland.  

 

Rewire the handset cord to the PCBA. 

 

Ringer Replacement 

 

Disconnect the ringer wiring from the terminal block on the PCBA. 

 

Remove the screws that hold the ringer to the housing. 

 

Install the new ringer and gasket. 

 

Reconnect the ringer wiring to the terminal block. 

 

Main Circuit Board Replacement 

 

Label any wiring attached to the circuit board. Disconnect wiring and ribbon cable. 

 

Remove the two screws holding the circuit board in place. Carefully remove the board. 

 

Install the new board and reconnect the wiring. 

 

If the configuration had been changed from the factory default settings reprogram the telephone. 

 

Test by making and receiving calls from another telephone. 

 

 
 

Summary of Contents for P6300

























Reviews: