GSi 40 Series Construction Manual Download Page 92

Page: 92 / 116

Ladder Section Assembly

The inside ladder package consists of the ladder, starter brackets, standoff brackets, reinforcement
straps, and ending bracket. The ladder should to be assembled before installing it to the bin structure.

What You Should Know

When assembling ladder sections, ensure all slip resistant ladder rungs are oriented in the same
direction.

NOTE:

A portion of the last ladder section may need to be cut to fit the proper length to the ground or to
the intermediate platform.

1. Place two ladder sections (A) together as shown.

2. Install a splice plate (C) to each outside channel, connecting the ladder sections (A).

3. Install flange bolts (D) to each inside channel as shown, connecting the ladder sections (A).

4. Install flange nuts (B) to each outside channel as shown, securing the ladder sections (A). Tighten to

the recommended torque specifications. Refer to

Bolt Torque Specifications, page 26

Figure 9-1

Assembling the inside ladder sections

Ladder section

Splice plate (LDR-4317)

5/16 in. flange nut (S-3611)

5/16 x 1 in. flange bolt with sealing
washer (S-10260)

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands