GSi 40 Series Construction Manual Download Page 62

Page: 62 / 116

12–Bolt Pattern Laminated Stiffener to Laminated Base Stiffener
with an Inserts to a Base Boot

Reference the following information when connecting a 12–bolt pattern laminated stiffener (CTS-4041XX)
to a laminated base stiffener (CTS-4050XX) with a inserts (CTS-4042XX and CTS-4051XX) to a base
boot (CTS-4045XX or CTS-4048XX).

Laminated stiffener (CTS-4041XX)

Base boot (CTS-4045XX or 4048XX)

Base Insert (CTS-4042XX)

3/8 x 1 in. flange bolt (S-7485)

Laminated base stiffener (CTS-4050XX)

3/8 in. flange nut (S-9426)

Close-punch base Insert (CTS-4051XX)

Completed assembly

NOTE:

Only place bolts where holes in the stiffeners align with holes in the sidewall sheet.

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands