GSi 40 Series Construction Manual Download Page 59 | Manualshive

Page: 59 / 116

background image

Chapter 6: Stiffeners

Laminated Base Stiffener (2 Ga) with Insert (2+12 to 2+10 Ga) to a
Base Boot

Reference the following information when connecting a laminated base stiffener with insert (CTS-4034XX
and CTS-4037XX) to a base boot (CTS-4045XX or CTS-4048XX).

A

Laminated base stiffener (CTS-4034XX)

B

Base Insert (CTS-4037XX)

C

Base boot (CTS-4045XX or CTS-4048XX)

D

3/8 x 1 in. flange bolt (S-7485)

E

3/8 in. flange nut (S-9426)

F

Completed assembly

NOTE:

Only place bolts where holes in the stiffeners align

with holes in the sidewall sheet.

Standard Stiffener to a 12–Bolt Pattern Laminated Stiffener with
Insert

Reference the following information when connecting a standard stiffener (CTS-4002XX) to a 12–bolt pat-
tern laminated stiffener (CTS-4041XX) with insert (CTS-4042XX).

A

Standard stiffener (CTS-4002XX)

B

Laminated stiffener (CTS-4041XX)

C

Insert (CTS-4042XX)

D

3/8 x 1 in. flange bolt (S-7485)

E

3/8 in. flange nut (S-9426)

F

Completed assembly

NOTE:

Only place bolts where holes in the stiffeners align

with holes in the sidewall sheet.

PNEG-4336

36 Ft. Diameter 40-Series Bins

59

«
...
57
58
59
60
61
...
»

Summary of Contents for 40 Series





















































































































Reviews:

No comments

Related manuals for 40 Series

Brand: Ecco Pages: 4

Brand: JD Squared Pages: 15

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

Brand: Jacobsen Pages: 6

Brand: iGuzzini Pages: 20

Brand: Harken Pages: 4

Brand: C.M.O Pages: 10

Brand: XM Fitness Pages: 10

Aspect Q-CARD 100-4T

Brand: idi Pages: 38

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: LANGER EMV-Technik Pages: 25

Electric Clamshell CSE12-208VCD

Brand: Lang Pages: 16

Brillion 3631-25

Brand: Landoll Pages: 138

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: Rational Pages: 16

Brand: Ultimate Healthcare Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands