GSi 40 Series Construction Manual Download Page 57

Page: 57 / 116

Chapter 6: Stiffeners

Laminated Stiffeners (2 Ga) with Inserts (10–12 Ga)

Reference the following information when connecting a laminated stiffener (CTS-4008XX) to an insert
(CTS-4010XX).

Laminated stiffener (CTS-4008XX)

Insert (CTS-4010XX)

3/8 x 1 in. flange bolt (S-7485)

3/8 in. flange nut (S-9426)

Completed assembly

NOTE:

Only place bolts where holes in the stiffeners

align with holes in the sidewall sheet.

Laminated Stiffener (2 Ga) with an Insert (10–12 Ga) to a Laminated
Base Stiffener (2 Ga) with a Base Insert (2–12 Ga)

Reference the following information when connecting a laminated stiffener and insert (CTS-4008XX and
CTS-4010XX) to a laminated base stiffener and base insert (CTS-4034XX and CTS-4037XX).

Laminated stiffener (CTS-4008XX)

Insert (CTS-4010XX)

Laminated base stiffener (CTS-4034XX)

Base insert (CTS-4037XX)

3/8 x 1 in. flange bolt (S-7485)

3/8 in. flange nut (S-9426)

Completed assembly

NOTE:

Only place bolts where holes in the stiffeners align

with holes in the sidewall sheet.

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands