GSi 40 Series Construction Manual Download Page 107

Page: 107 / 116

Chapter 9: Accessories

Temperature Cable Support Package Instructions for Eave Heights
Greater than 40 ft. - 5 in. (12.32 m) (Optional)

1. For 36 ft. (10.97 m) diameter two post bins, the temperature cable support package shall span three

roof panels.

2. A rafter support system (included in each package) will be necessary for temperature cable

installation in 36 ft. (10.97 m) bins.

3. One package should be provided for each cable in the tank with the exception of the center cable.

4. All packages include hanging angle and a cable support channel (K).

5. Each set of rafters should carry only one temperature cable.

6. Each kit will contain two rafter sections (C and D), which when spliced will reach from the center

collar (G) to the bin wall. The lower rafter (C) will be bolted into the stiffener bracket (A) using
3/8 x 1 in. flange bolts (B) and 3/8 in. hex nuts (O).

Figure 9-14

Lower rafter assembly

Stiffener bracket (CRP-4758)

Lower rafter (CRP-7241)

3/8 x 1 in. flange bolt (S-7487)

3/8 in. hex nut (S-456)

PNEG-4336

36 Ft. Diameter 40-Series Bins

107

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands