background image

15

English (US)

15.1.10 Three-phase pumps, 3-10 hp

Group 3: Power supply (terminals L1, L2, L3)

Fig. 7

Connection terminals 

A galvanic separation must fulfill the requirements for reinforced 
insulation including creepage distances and clearances specified 
in EN 60335.

15.2 Three-phase pumps, 15-30 hp

15.2.1 Preparation

Before connecting the E-pump to the power supply, take the 
issues illustrated in the figure below into consideration.

Fig. 8

Power supply-connected pump with power switch, 
backup fuses, additional protection and protective 
grounding

15.2.2 Protection against electric shock - indirect contact

EN 61800-5-1 specifies that the pump must be stationary and 
installed permanently when the leakage current is > 10 mA.
One of the following requirements must be fulfilled:
• A single protective ground lead (7 AWG minimum copper)

Fig. 9

Connection of a single protective ground lead using 
one of the leads of a 4-core power cable (7 AWG 
minimum)

• Two protective ground leads of the same cross-sectional area 

as the power supply leads, with one lead connected to an 
additional ground terminal in the terminal box.

Fig. 10

Connection of two protective ground leads using two of 
the leads of a 5-core power supply cable

Protective ground leads must always have a yellow/green (PE) or 
yellow/green/blue (PEN) color marking. 

T

M

05

 2

9

8

5

 08

12

Warning
The user or the installer is responsible for the 
installation of correct grounding and protection 
according to current national and local 
standards. All operations must be carried out by 
qualified personnel.

Warning
Never make any connections in the pump 
terminal box unless all electric supply circuits 
have been switched off for at least 5 minutes.
Note for instance that the signal relay may be 
connected to an external supply which is still 
connected when the power supply is 
disconnected.

Warning
The surface of the terminal box may be above 
158 °F (70 °C) when the pump is operating.

6: GND (frame)
5: +10 V
4: Setpoint input
3: GND (frame)
2: Start/stop

Group

 1

Group 

2

Group

 3

13: GND (frame)
12: Analog output
11: Digital input 4
10: Digital input 3
1: Digital input 2
9: GND (frame)
8: +24 V
7: Sensor input
B: RS-485B
Y: Screen
A: RS-485A

TM

0

0

 9

270

 4

696

Warning
The pump must be grounded in accordance with 
national regulations.
As the leakage current of 15-30 hp motors is 
> 10 mA, take extra precautions when grounding 
these motors.

TM

0

4

 3

021

 3

508

TM0

3

 8

60

6 2

0

0

7

L1

L2

L3

L2

L1

L3

PE

ELCB

Summary of Contents for VLSE

















































Reviews: