background image

13

English (US)

7.5 Wiring diagrams

Fig. 16 Three thermal switches (PTO, bimetallics)

Fig. 17 Three PTC sensors

7.6 Direction of rotation

When the electrical connections have been carried out, 
check that the propeller is rotating in the correct direction. 
When viewed from the motor, the propeller should rotate 
clockwise. 
An arrow on the motor housing shows the correct direction of 
rotation.

If the propeller rotates in the wrong direction, interchange two 
phases of the mains supply (L1, L2, L3).

7.7 Protection from electro-chemical corrosion

Two different metals or alloys cause electro-chemical corrosion if 
they are connected by an electrolyte. This applies if more than 
one pump is installed in the same tank. We recommend the 
following additional protection:

galvanic separation of the earth conductor from the neutral 
conductor or

galvanic separation of the mains supply by means of an 
isolation transformer.

The earth conductor must be separated in such a way as to 
ensure that no direct current can flow through it. It must still 
function as a protective conductor. This can be achieved with a 
limiting unit (polarization cell or anti-parallel diode) or an isolation 
transformer.

Fig. 18 Protection from electro-chemical corrosion

7.8 Frequency converter operation

The SRP pumps are designed for frequency converter operation 
in the 40 to 60 Hz range. However the SRP pumps can run down 
to 10 Hz in min frequency, having sufficient cooling in mind.

T

M

02

 49

40

 18

02

Terminals

Description

1, 2, 3, 4, 5, 6

Ends of the three stator windings
(U1, U2, V1, V2, W1, W2) 

11, 12

Thermal switches (F6)

21, 22

Leak sensor in gearbox (B)

TM

02 49

32 18

02

Terminals

Description

1, 2, 3, 4, 5, 6

Ends of the three stator windings
(U1, U2, V1, V2, W1, W2) 

31, 32

PTC sensors (according to DIN 44 081) 
(

1, 

2, 

3)

21, 22

Leak sensor in gearbox (B)

B

LS

V2

U2

W2

W1

V1

U1

PE

PTO

LS

V2

U2

V1

U1

W2

W1

PTC

PE

T

M

02

 94

80

 27

04

Pos.

Designation

1

Limiting unit

2

Earth conductor

3

Isolation transformer

Warning

When using an isolation transformer, the ratio 
between starting current and rated current (I

A

/I

N

must not be altered.

L1
L2
L3
N
PE 

1

3

2

2

Summary of Contents for SRP Series






















Reviews: