background image

3

English (US)

English (US) 

Installation and operating instructions

Original installation and operating instructions.

CONTENTS

Page

1. Limited warranty

Products manufactured by GRUNDFOS PUMPS CORPORATION 
(Grundfos) are warranted to the original user only to be free of 
defects in material and workmanship for a period of 24 months 
from date of installation, but not more than 30 months from date 
of manufacture. Grundfos' liability under this warranty shall be 
limited to repairing or replacing at Grundfos' option, without 
charge, F.O.B. Grundfos' factory or authorized service station, 
any product of Grundfos' manufacture. Grundfos will not be liable 
for any costs of removal, installation, transportation, or any other 
charges which may arise in connection with a warranty claim. 
Products which are sold but not manufactured by Grundfos are 
subject to the warranty provided by the manufacturer of said 
products and not by Grundfos' warranty. Grundfos will not be 
liable for damage or wear to products caused by abnormal 
operating conditions, accident, abuse, misuse, unauthorized 
alteration or repair, or if the product was not installed in 
accordance with Grundfos' printed installation and operating 
instructions.
To obtain service under this warranty, the defective product must 
be returned to the distributor or dealer of Grundfos' products from 
which it was purchased together with proof of purchase and 
installation date, failure date, and supporting installation data. 
Unless otherwise provided, the distributor or dealer will contact 
Grundfos or an authorized service station for instructions. Any 
defective product to be returned to Grundfos or a service station 
must be sent freight prepaid; documentation supporting the 
warranty claim and/or a Return Material Authorization must be 
included if so instructed.
GRUNDFOS WILL NOT BE LIABLE FOR ANY INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, LOSSES, OR EXPENSES 
ARISING FROM INSTALLATION, USE, OR ANY OTHER 
CAUSES. THERE ARE NO EXPRESS OR IMPLIED 
WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND 
THOSE WARRANTIES DESCRIBED OR REFERRED TO 
ABOVE.
Some jurisdictions do not allow the exclusion or limitation of 
incidental or consequential damages and some jurisdictions do 
not allow limit actions on how long implied warranties may last. 
Therefore, the above limitations or exclusions may not apply to 
you. This warranty gives you specific legal rights and you may 
also have other rights which vary from jurisdiction to jurisdiction.

1.

Limited warranty

3

2.

Symbols used in this document

4

3.

General information

4

4.

General description

4

4.1

Pumps without factory-fitted sensor

4

4.2

Pumps with pressure sensor

4

4.3

Settings

4

5.

Mechanical installation

4

5.1

Motor cooling

4

5.2

Outdoor installation

4

6.

Electrical connection

4

6.1

Single-phase pumps

5

6.2

Three-phase pumps, 1 - 10 Hp

6

6.3

Three-phase pumps, 15 - 30 Hp

9

6.4

Signal cables

11

6.5

E-pump electrical connections

11

6.6

Bus connection cable

12

7.

Modes

12

7.1

Overview of modes

12

7.2

Operating mode

12

7.3

Control mode

12

8.

Setting up the pump

13

8.1

Factory setting

13

9.

Setting by means of control panel

13

9.1

Setting of operating mode

13

9.2

Setpoint setting

13

10.

Setting by means of R100

14

10.1 Menu OPERATION

16

10.2 Menu STATUS

17

10.3 Menu INSTALLATION

18

10.4 Typical display settings for constant pressure E-pumps 24
10.5 Typical display settings for analog input E-pumps

25

11.

Setting by means of PC Tool E-products

26

12.

Priority of settings

26

13.

External forced-control signals

26

13.1 Start/stop input

26

13.2 Digital input

26

14.

External setpoint signal

27

15.

Bus signal

27

16.

Other bus standards

27

17.

Indicator lights and signal relay

28

18.

Insulation resistance

30

19.

Emergency operation (only 15 - 30 Hp)

30

20.

Maintenance and service

31

20.1 Cleaning of the motor

31

20.2 Relubrication of motor bearings

31

20.3 Replacement of motor bearings

31

20.4 Replacement of varistor (only 15 - 30 Hp)

31

20.5 Service parts and service kits

31

21.

Technical data - single-phase pumps

31

21.1 Supply voltage

31

21.2 Overload protection

31

21.3 Leakage current

31

21.4 Inputs/outputs

31

22.

Technical data - three-phase pumps, 1 - 10 Hp

32

22.1 Supply voltage

32

22.2 Overload protection

32

22.3 Leakage current

32

22.4 Inputs/output

32

23.

Technical data - three-phase pumps, 15 - 30 Hp

33

23.1 Supply voltage

33

23.2 Overload protection

33

23.3 Leakage current

33

23.4 Inputs/output

33

23.5 Other technical data

33

24.

Disposal

34

DBP-1 - GRUNDFOS PUMP CRE - 99392005

Summary of Contents for SPKE Series






































Reviews: