background image

En
gl

is

h (
G

B)

2

English (GB) 

Installation and operating instructions

Original installation and operating instructions

These installation and operating instructions 
describe Grundfos MTH.
Sections 1-3 give the information necessary to be 
able to unpack, install and start up the product in a 
safe way.
Sections 4-8 give important information about the 
product, as well as information on service, fault 
finding and disposal of the product.

CONTENTS

Page

1. General information

1.1 Hazard statements

The symbols and hazard statements below may 
appear in Grundfos installation and operating 
instructions, safety instructions and service 
instructions.

The hazard statements are structured in the 
following way:

1.

General information

2

1.1 Hazard statements

2

1.2 Notes

3

2.

Installing the product

3

2.1 Mechanical installation

3

2.2 Tank mounting

3

2.3 Inlet conditions

5

2.4 Electrical connection

5

3.

Starting up the product

7

3.1 Operating the product

7

4.

Product introduction

7

4.1 Applications

7

4.2 Identification

7

5.

Servicing the product

8

5.1 Contaminated products

9

5.2 Maintaining the product

9

5.3 Filters

9

5.4 Periodic checks

9

6.

Fault finding the product

10

7.

Technical data

11

7.1 Operating conditions

11

7.2 Sound pressure level

11

8.

Disposing of the product

11

Read this document before installing the 
product. Installation and operation must 
comply with local regulations and accepted 
codes of good practice.

DANGER

Indicates a hazardous situation which, if 
not avoided, will result in death or serious 
personal injury.

WARNING

Indicates a hazardous situation which, if 
not avoided, could result in death or 
serious personal injury.

CAUTION

Indicates a hazardous situation which, if 
not avoided, could result in minor or 
moderate personal injury.

SIGNAL WORD

Description of hazard

Consequence of ignoring the warning.
- Action to avoid the hazard.

Summary of Contents for MTH 10



















Reviews: