background image

16

Hookup auto-coupling system

, see fig. C, 

page 534.

Proceed as follows:

1. Fit the crossbar in the tank. 

2. Fit the adapted piece of pipe for the movable part 

of the hookup auto coupling to the pump 
discharge port.

3. Fasten a shackle and a chain to the movable part 

of the hookup auto coupling.

4. Clean out debris from the tank before lowering 

the pump. 

5. Lower the pump into the tank by means of the 

chain secured to the pump lifting bracket.

6. Hang up the end of the chain on a suitable hook 

at the top of the tank and in such a way that the 
chain cannot come into contact with the pump 
housing. 

7. Adjust the length of the motor cable by coiling it 

up on a relief fitting to ensure that the cable is not 
damaged during operation. Fasten the relief 
fitting to a suitable hook at the top of the tank. 
Make sure that the cables are not sharply bent or 
pinched.

8. Connect the motor cable and the monitoring 

cable, if any.

8.2 Free-standing submerged installation 

Pumps for free-standing submerged installation can 
stand freely on the bottom of the tank or similar 
location. See fig. D, page 535, and fig. E, page 536.

In order to facilitate service on the pump, fit a flexible 
union or coupling to the discharge line for easy 
separation.

If a hose is used

, make sure that the hose does not 

buckle and that the inside diameter of the hose 
matches that of the discharge port. 

If a rigid pipe is used

, the union or coupling, non-

return valve and isolating valve should be fitted in 
the order mentioned, when viewed from the pump. 

If the pump is installed in muddy conditions or on 
uneven ground, it is recommended to support the 
pump on bricks or a similar support. 

Proceed as follows:

1. Fit a 90 ° elbow to the pump discharge port, 

and connect the discharge pipe or hose.

2. Lower the pump into the liquid by means of a 

chain secured to the lifting bracket of the pump. 
It is recommended to place the pump on a plane, 
solid foundation. Make sure that the pump is 
hanging from the chain and 

not

 the cable.

3. Hang up the end of the chain on a suitable hook 

at the top of the tank and in such a way that the 
chain cannot come into contact with the pump 
housing. 

4. Adjust the length of the motor cable by coiling it 

up on a relief fitting to ensure that the cable is not 
damaged during operation. Fasten the relief 
fitting to a suitable hook. Make sure that the 
cables are not sharply bent or pinched. 

5. Connect the motor cable and the monitoring 

cable, if any.

9. Electrical connection

The electrical connection should be carried out in 
accordance with local regulations. 

Note

If several pumps are installed in the 
same tank, the pumps must be installed 
at the same level in order to allow 
optimum pump alternation. 

Caution

The pump must not be used with 
a frequency converter.

Warning

The pump must be connected to an 
electrical panel in accordance with 
local regulations. The electrical panel 
typically includes fuses, main switch 
and earth leakage circuit breaker with 
a contact separation according to 
EN 60204-1, 5.3.2.

It must be possible to lock the mains 
switch in position 0. Type and 
requirements as specified in 
EN 60204-1, 5.3.2.

The pump incorporates a motor-
protective circuit breaker and 
all control logic.

Warning

If the pump has an Ex mark on the 
nameplate, make sure that the pump 
is connected in accordance with the 
instructions given in this booklet.

Warning

The explosion protection classification 
of the pump is CE 

 II 2 G, Ex bcd IIB 

T4 Gb. See section 4.2.
The classification of the installation 
site must in each individual case be 
approved by the local authorities. 

The CIU unit, if used, (see section 9.1) 
must not be installed in potentially 
explosive environments.

Warning

On explosion-proof pumps, make sure 
that an external earth conductor is 
connected to the external earth 
terminal on the pump using a 
conductor with a secure cable clamp. 
Clean the surface for external earth 
connection, and fit the cable clamp.

The cross section of the earth 
conductor must be at least 4 mm

2

, e.g. 

type H07 V2-K (PVT 90 °) yellow/green.

Make sure that the earth connection is 
protected from corrosion.

Summary of Contents for DP 10.50





















Reviews: