Grundfos DP 10.50 Original Installation And Operating Instructions Download Page 17

Page: 17 / 20

12.9 Service kits

The service kits in the table below are available for all pumps.

The kits can be ordered as required.

Warning

Before starting work on the pump, make sure that the fuses have been removed or the mains
switch has been switched off. It must be ensured that the power supply cannot be
accidentally switched on.

All rotating parts must have stopped moving.

Service kit

Contents

Pump type

Material

Product number

Shaft seal kit

Shaft seal complete

0.6 - 1.5 kW

BQQP

96106536

BQQV

96645161

2.6 kW

BQQP

96076123

BQQV

96645275

O-ring kit

O-rings and gaskets for oil screws

0.6 - 1.5 kW

NBR

96115107

FKM

96646049

2.6 kW

NBR

96115108

FKM

96646060

Impeller

Impeller complete with adjusting
screw, shaft screw and key

EF 30.50.06

96115101

EF 30.50.09

96115109

EF 30.50.11

96115102

EF 30.50.15

96115103

DP 10.50.09

96115104

DP 10.50.15

96115105

DP 10.65.26

96115106

Oil

1 litre of oil, type Shell Ondina 917.
See section

12. Maintenance and

service

for required quantity in oil

chamber.

All types

96076171

Lifting bracket

Lifting bracket and screw

0.6 - 1.5 kW

96984147

2.6 kW

96984148

Power plug

Plug for power supply and O-rings for
cover

All types

96984144

Protective cap
for level sensor

Protective cap and O-rings for cover
and sensor

All types

96898081

Level sensor

Level sensor, protective cap and
O-rings for cover and sensor

Standard pumps

96898082

Ex pumps

96984130

Dry-running
sensor

Dry-running sensor and O-rings for
cover and sensor

Standard pumps

96898083

Ex pumps

96984131

unit
Single-phase

Cover with electronics and O-rings for
cover

Single-phase

pumps

96898085

Single-phase

Ex pumps

96984145

unit
Three-phase

Cover with electronics and O-rings for
cover

Three-phase

pumps

96898086

Three-phase

Ex pumps

96984146

Pt1000 sensor

Pt1000 sensor and bracket

All types

96984143

Summary of Contents for DP 10.50





















Search results

Summary of Contents for DP 10.50

Reviews:

Related manuals for DP 10.50

Brands by name

Popular brands

Grundfos DP 10.50, Original Installation And Operating Instructions

Search results

Summary of Contents for DP 10.50

Reviews:

Related manuals for DP 10.50

Brands by name

Popular brands