Grundfos 98916439 Installation And Operating Instructions Manual Download Page 5

Page: 5 / 36

GRUNDFOS

INSTRUCTIONS

www.grundfos.co.uk

Page 4 of 35

2.0 Symbols used in this document

WARNING

If these safety instructions are not observed, it may result in personal injury or damage

to property.

WARNING

If these instructions are not observed, it may lead to electric shock with consequent

risk of serious personal injury or death.

CAUTION

If these safety instructions are not observed, it may result in malfunction or
damage to the equipment

NOTE

Notes or instructions that make the job easier and ensure safe operation

3.0 Scope of these Instructions

These Installation and Operating instructions apply to the:



Grundfos FireSAFE

(Domestic Range of units)

For Technical Information consult the

FireSAFE

Datasheet and the Technical information

section of this manual.

For CM Pump specific information please consult the CM Installation and Operating manual
supplied with the product documentation.

All of the above documents can also be found on the Grundfos Product Center website at:
www.grundfos.co.uk

4.0 Product Identification

The

FireSAFE

unit has a silver label attached to the top of the front cover.

This label gives the following key information.

CAUTION

NOTE

Part no

Serial No.

Electrical Data

Hydraulic Data

Summary of Contents for 98916439





































Search results

Summary of Contents for 98916439

Reviews:

Related manuals for 98916439

Brands by name

Popular brands

Grundfos 98916439, Installation And Operating Instructions Manual

Search results

Summary of Contents for 98916439

Reviews:

Related manuals for 98916439

Brands by name

Popular brands