background image

  

 

GRUNDFOS 

INSTRUCTIONS

 

www.grundfos.co.uk 

Page 29 of 35  

                                                      

     

 
Ensure any outgoing signals from the 

FireSAFE

 unit are not going to cause 

activation of: 

 

Fire alarms/beacons 

 

Fire alarm control panel  

 

Fire service response or fire monitoring service response 

 

Any other warning/monitoring devices installed (eg. SMS to mobile device) 
 

Consideration should be given to contacting any response services beforehand and 

informing them of the de-commissioning and dismantling of the 

FireSAFE

 unit.  

 

   Isolate the electrical supply ensuring it cannot be turned back on   

 

   Disconnect the electrical supply from the 

FireSAFE

 unit 

 

Press the Test/Reset button on the control panel to silence the internal buzzer 

 

Close the system isolating valve on the suction side of the 

FireSAFE

 unit 

 

Remove the two bolts holding the front cover in place 

 

Lift off the front cover and disconnect the earth bonding wire to the front cover and 
place the cover in safe place out of the way 

 

   The sprinkler system may still be pressurised from the 

FireSAFE

 internal non- 

return valve to the sprinkler head. Drain the water from the system from the system 
drain point; beware of pressure in the system. Close the system isolating valve on the 
discharge side of the 

FireSAFE

 unit 

 

Drain the 

FireSAFE

 unit and system pipework from the point chosen to disconnect the 

FireSAFE

 unit on the suction side of the unit.   

 

Drain the 

FireSAFE

 unit by removing the drain plug in the pump  

 

Dismantle the pipework and base/wall fixings.  

 

Remove the set with appropriate handling equipment and procedures.  

 

16.3 Disposal  

The 

FireSAFE

 unit has valuable recyclable components.   

  

Disposal of this product or parts of it must be carried out according to the following guidelines:  

 

Use the local public or private waste collection service.  

 

The materials/components used need to be segregated according to the disposal 
receivers requirements.  

 

In case such waste collection services do not exist or cannot handle the materials used 
in the product, please deliver the product or any hazardous materials from it to your 
nearest Grundfos company or service workshop.  

  

Local and National environmental legislation must always be complied with.  

 

 

NOTE 

Summary of Contents for 98916439





































Reviews: