Grundfos 98916439 Installation And Operating Instructions Manual Download Page 29

Page: 29 / 36

GRUNDFOS

INSTRUCTIONS

www.grundfos.co.uk

Page 28 of 35

15.0 Spare Parts List

Part no.

Description

Parts included

99019805

I & O Manual

99019808

CM3-3 Pump

CM3-3 pump, with I & O manual

99019809

CM3-5 Pump

CM3-5 pump, with I & O manual

99019810

CM5-3 Pump

CM5-3 pump, with I & O manual

99019811

CM5-4 Pump

CM5-4 pump, with I & O manual

99019812

CM10-2 Pump

CM10-2 pump, with I & O manual

99019823

CM10-3 Pump

CM10-3 pump, with I & O manual

99019824

CM3/5 Discharge assembly

NRV and fittings, with I & O manual

99019825

CM10 Discharge assembly

NRV and fittings, with I & O manual

99019826

Primary Pressure switch
(DANFOSS)

Primary pressure switch, with I & O manual

99079031

Secondary Pressure switch
(GEMS)

Secondary pressure switch, with I & O manual

99019827

Pressure Gauge

Pressure Gauge, with I & O manual

98807985

Controller

Controller, with I & O manual

99015438

Fuse kit

Controller Fuse, F1 500 mA,
Pump Fuse, F2 15 A, with I & O Manual

99019829

Small Fixings

Screws and nuts
with I & O Manual

16.0 De-commissioning, dismantling and disposal.

The building will be without the Fire protection that the

FireSAFE

unit gives once

decommissioned and an alternative measure to provide protection against fire should be
considered. The owner of the building, insurer and any inhabitants must be informed of this.

16.1 De-commissioning

De-commissioning is the process of taking out of service the

FireSAFE

unit.

Reasons for this could be:



Replacing with another unit



Upgrading the unit



Removing the system altogether

16.2 Dismantling

Always make sure that adequate provision is made to capture any water
drained from the system and

FireSAFE

unit when dismantling.

Always make sure that adequate water spill protection for flooring etc is in
place before dismantling and draining any part of the system or

FireSAFE

unit.

Appropriate PPE must be worn. (including eye protection and gloves)

NOTE

Summary of Contents for 98916439





































Search results

Summary of Contents for 98916439

Reviews:

Related manuals for 98916439

Brands by name

Popular brands

Grundfos 98916439, Installation And Operating Instructions Manual

Search results

Summary of Contents for 98916439

Reviews:

Related manuals for 98916439

Brands by name

Popular brands