Grunbeck softliQ:SD Series Operation Manual Download

Page: 59 / 80

Malfunction

59 | 80

-B

liQ

-SD

Malfunction

WARNING:

Danger of contaminated drinking water due to stagnation.

● Risk of infectious diseases.

► Have malfunctions remedied immediately.

The water softener softliQ indicates malfunctions on the display. As soon as a fault appears,
the touch-screen display changes to the basic display and remains active until the fault is
rectified.

► If malfunctions cannot be remedied by the instructions given below, contact

Grünbeck's technical service / authorised service company.

► Have your equipment data (refer to chapter 1.7) handy.

8.1

Display messages

Acknowledge the display signal with rectify.

Watch the display.

If the fault occurs again, compare the display message with the following table.

8.1.1

Warning messages (yellow symbols)

Display shows

Explanation

Remedy

Perform maintenance

since … days

Only displayed if
maintenance interval is
activated.

Notify Grünbeck's technical service /
authorised service company.

SD21 and SD23 only:

Leak at the

softliQ installation location

Water sensor has
electrical connection.

Check whether water is leaking.
If necessary, close the main valve of
the house installation.

SD21 and SD23 only:

Salt supply low!

Please refill!

Sufficient for: xy days

(order no. 127 001)

Salt supply low.

Refill salt tablets (refer to
chapter 6.3).

Confirm with Rectify.

Summary of Contents for softliQ:SD Series

















































































Search results

Summary of Contents for softliQ:SD Series

Reviews:

Related manuals for softliQ:SD Series

Brands by name

Popular brands

Grunbeck softliQ:SD Series, Operation Manual

Search results

Summary of Contents for softliQ:SD Series

Reviews:

Related manuals for softliQ:SD Series

Brands by name

Popular brands