Gronomics WRC PB 28-48 Assembly Instruction Manual Download Page 1

www.gronomics.com 

East Bethel, MN USA 

763-753-7374

Continued

WRC Patio Bar

Assembly Instruction

1

Parts Identi

fi

 cation Box 1

Stack matching pieces in piles. Using 
the parts list, locate and count the 
individual pieces and verify that you 
have received the correct number of 
pieces.

If any pieces are missing or 
replacement parts are required, 
contact Gronomics at 1-855-299-
6727.

NOTE: It is recommend to place a 
protective layer between the ground 
and the pieces during assembly. 
This will help prevent damage to the 
pieces.

Parts List Box 1 of 2

ITEM

QTY.

PART #

DESCRIPTION

1

1

28481

Bar Top, 47” x 26-1/4” x 1-5/8”

2

1

T-28484

Front Panel Tongue & Groove Board (Top) 5-1/4” x 34-3/4” x 5/8”

3

7

28484

Front Panel Tongue & Groove Boards 5-1/4” x 34-3/4” x 5/8”

4

2

K-28484

Toe Kick Plate (TK) (one w/Logo) 5-1/4” x 34-3/4” x 5/8”

5

4

SS-28485

Sand Shelf, Tongue & Groove Boards (SS) 5-1/4” x 34-3/4” x 5/8”

6

4

BS-28485

Bottom Shelf, Tongue & Groove Boards (BS) 5-1/4” x 34-3/4” x 5/8”

7

4

TS-28485

Top Shelf, Tongue & Groove Boards (TS) 5-1/4” x 34-3/4” x 5/8”

8

1

SS-21434

Sand Shelf, Narrow Board (SS) 2-1/4” x 34-1/2” x 5/8”

9

1

BS-21234

Bottom Shelf, Narrow Board (BS) 2-1/2” x 34-1/2” x 5/8”

10

1

TS-21234

Top Shelf, Narrow Board (SS) 2-1/2” x 34-1/2” x 5/8”

11

1

28486

Foot Rest, 3-1/4” x 38-3/4” x 3-1/4”

12

1

HTUS 28-28

Umbrella Stand

13

40

CS8-112ZY

Screws, GRK (front panel & toe kick boards) 8 x 1-1/2”

14

6

RSS14-212ZY Screws, RSS GRK (table top) 1/4” x 2-1/2”

15

4

RSS14-312ZY Screws, RSS GRK (foot rest) 1/4” x 3-1/2”

1

2

3

4

5

6

7

8

9

12

12

10

10

11

11

13

13

14

14

15

15

PB 28-48

Packaged & Inspected by:

Date:

Torx® T15

Torx® T25

Torx® T25

14

14

15

15

13

13

Summary of Contents for WRC PB 28-48









Reviews: