Model G1014Z/G1014ZX (Mfd. Since 08/22)
-17-
G1014Z Inventory
Box 1 (Figures 9–11)
Qty
A. Sander Unit ................................................. 1
B. Stand Legs .................................................. 4
C. Long Lower Braces ..................................... 2
D. Long Upper Braces ..................................... 2
E. Short Lower Braces ..................................... 2
F. Short Upper Braces ..................................... 2
G. Sanding Belt 6" x 48" .................................. 1
H. Dust Port 2
1
⁄
2
" (Black) .................................. 1
I. Work Table .................................................. 1
J. Miter Gauge ................................................. 1
K. Back Stop .................................................... 1
L. Rubber Feet ................................................ 4
M. Table Support Rod ...................................... 1
N. Quick Release Lever Stud 6" ...................... 1
O. Short Lever Arm .......................................... 1
P. Quick Release Lever Handle ...................... 1
Q. Idler Roller ................................................... 1
R. Idler Roller Guard ........................................ 1
S. Dust Port 2" (Green) .................................... 1
T. Cast Iron Plate ............................................. 1
U. Sanding Disc 9" ........................................... 1
Hardware & Tools (not shown)
Qty
•
Hex Wrench 4mm ........................................ 1
•
Hex Bolts
5
⁄
16
"-18 x 1" (Feet) ........................ 4
•
Hex Nuts
5
⁄
16
"-18 (Feet, Stand) .................. 36
•
Flat Washers
5
⁄
16
" (Feet, Stand) ................. 40
•
Hex Bolts
5
⁄
16
"-18 x
1
⁄
2
" (Stand & Sander) .... 4
•
Carriage Bolts
5
⁄
16
"-18 x
1
⁄
2
" (Stand) ........... 32
•
Phillip Head Screws 10-24 x
3
⁄
8
"
(2
1
⁄
2
" Dust Port) ............................................ 4
•
Hex Nuts 10-24 (2
1
⁄
2
" Dust Port) .................. 4
•
Flat Washers #10 (2
1
⁄
2
" Dust Port) ............... 4
•
Hex Nuts
3
⁄
8
"-16 (Quick Release Lever) ...... 2
•
Thumb Knobs
1
⁄
4
"-20 x
1
⁄
2
" (Sander Unit) ..... 2
•
Flat Washers
1
⁄
4
" (Sander Unit) .................... 2
•
Thumb Knobs M5-.8 x 10 (Roller Guard) .... 2
•
Flat Washers #10 (Roller Guard) ................. 2
•
Lock Washers #10 (Roller Guard) ............... 2
Figure 9. G1014Z sander unit.
A
Figure 10. G1014Z stand components.
B
C
D
E
F
Figure 11. Loose inventory items.
V
H
I
J
K
L
M
O
G
N
U
P
Q
R
S
T
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
