Grizzly G0866, Owner'S Manual, Page: 98 / 100

-96-
Model G0866 (Mfd. Since 11/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
KICKBACK HAZARD!
Do not insert more than
one board at a time. Stock
may be ejected at a high
rate of speed from this
machine.
PINCH HAZARD!
Keep hands away from pinch
points during operation.
Severe injury could occur if
hands get caught between
feed belt and stock or
between pressure roller and
stock.
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
WARNING!
KEEP DOOR
CLOSED WHILE
OPERATING!
This machine is prewired for 220V
operation. To operate at 440V,
follow critical voltage conversion
instructions in the user manual
included with this machine.
Failure to follow these instructions
will damage the machine and void
the warranty!
220 VOLT
WARNING!
KEEP DOOR
CLOSED WHILE
OPERATING!
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
To reduce the risk of serious injury while using this machine:
1. Read and understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Properly ground machine—connect to permanently grounded metal wiring system or
an equipment-grounding conductor.
4. Keep hands clear of moving parts during operation.
5. Never touch moving sandpaper or conveyor belt.
6. Never sand more than one board at a time.
7. Make sure sander is properly assembled, adjusted, and stable before operating. Only
operate with doors and panels closed and secured.
8. Be aware of pinch points located at the edge of conveyor and while lifting and
lowering conveyor table.
9. Only remove jammed pieces when machine is stopped and disconnected from power.
10. Keep all guards and covers in place during operation.
11. Never allow anyone to stand directly in front of or near outfeed end of machine.
12. Turn motor OFF, disconnect power, and make sure machine has come to complete
stop before changing sandpaper or servicing.
13. Do not wear loose clothing, gloves, jewelry, or other articles that can get entangled.
Tie back long hair and roll up sleeves.
14. Do not expose to rain or use in wet locations.
15. Do not operate under influence of drugs or alcohol, or if tired.
16. Prevent unauthorized use by children or untrained users; restrict access or disable
machine when unattended.
Front Sanding Motor: 15 HP, 220V, 36.7A, 3-Ph, 60 Hz
Rear Sanding Motor: 15 HP, 220V, 36.7A, 3-Ph, 60 Hz
Feed Motor: 2 HP, 220V, 6A, 3-Ph, 60 Hz
Table Elevation Motor: 1/4 HP, 220V, 1.2A, 3-Ph, 60 Hz
Full-Load Current Rating: 79.4A @ 220V, 39.9A @ 440V
Drum Surface Speed: 3600 FPM (Front), 2800 FPM (Rear)
Feed Rate: 7–68 FPM
Maximum Board Width: 36-1/2"
Maximum Board Thickness: 6"
Minimum Board Thickness: 3/16"
Minimum Board Length: 12"
Sanding Belt Size: 37" x 75"
Infeed Sanding Drum Size: 8.7" (Front), 5" (Rear)
Outfeed Sanding Drum Diameter: 5"
Required Air Pressure: 57–75 PSI
Weight: 3417 lbs.
Specifications WARNING!
Date
Mfd. for Grizzly in Taiwan
Serial Number
MODEL G0866
37" WIDE-BELT SANDER
W/INDUSTRIAL ROLLER
REMOVE SANDING BELT(S) AND
CLEAN RUST PREVENTATIVE
FROM UPPER DRUM(S)
BEFORE USING THIS
MACHINE.
9201
9202
9203
9204
9205
9205
9206
9206 9207
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
9208
9209
9209
9210
9211
9212
9213
9214
9215
9216
9217
9218
9210
9210
NOTICE
Press and hold this button for
10 seconds to switch display
between metric and SAE units.
220 V :
440 V :
10A 33A 36A
SAFE DAMAGE CAUTION
30A 68A 72A
SAFE DAMAGE CAUTION
Model: G0866
AMPERAGE LOAD CHART
9219
9220
G0866
grizzly.com
Position of this plate is factory set to allow maximum safe sanding depth. DO
NOT adjust or remove. Failure to do so could seriously damage machine.
NOTICE
On junction
boxes
REF PART # DESCRIPTION REF PART # DESCRIPTION
9201 P08669201 POSITION PLATE NOTICE LABEL 9211 P08669211 STOP REMOVE BELTS HANG TAG
9202 P08669202 GRIZZLY NAMEPLATE-LARGE 9212 P08669212 CONVERSION FRACTION
9203 P08669203 MODEL NUMBER LABEL 9213 P08669213 SANDER BELT PINCH LABEL
9204 P08669204 MACHINE ID LABEL 9214 P08669214 GRIZZLY.COM LABEL
9205 P08669205 DISCONNECT POWER LABEL 9215 P08669215 KICKBACK HAZARD LABEL
9206 P08669206 KEEP DOOR CLOSED LABEL 9216 P08669216 READ MANUAL LABEL
9207 P08669207 PREWIRED 220V LABEL 9217 P08669217 SWITCH DISPLAY NOTICE LABEL
9208 P08669208 RESPIRATOR/GLASSES LABEL 9218 P08669218 TOUCH-UP PAINT, GRIZZLY PUTTY
9209 P08669209 ELECTRICITY-SMALL LABEL 9219 P08669219 AMPERAGE LOAD CHART LABEL
9210 P08669210 ELECTRICITY-LARGE LABEL 9220 P08669220 TOUCH-UP PAINT, GRIZZLY GREEN
Labels & Cosmetics
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
G0866 Machine Labels A
(12.21.18)
• Scale= 1:1 (unless otherwise noted) • Labels MUST be made of chemical-resistant material
G0866
COLOR CODES
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval.
If
artwork changes are required, contact us immediately at
manuals@grizzly.com
.
PANTONE 151 C or RAL 2005
WARNING
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
GRIZZLY GREEN
PANTONE 568C
To reduce the risk of serious injury while using this machine:
1. Read and understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Properly ground machine—connect to permanently grounded metal wiring system or
an equipment-grounding conductor.
4. Keep hands clear of moving parts during operation.
5. Never touch moving sandpaper or conveyor belt.
6. Never sand more than one board at a time.
7. Make sure sander is properly assembled, adjusted, and stable before operating. Only
operate with doors and panels closed and secured.
8. Be aware of pinch points located at the edge of conveyor and while lifting and
lowering conveyor table.
9. Only remove jammed pieces when machine is stopped and disconnected from power.
10. Keep all guards and covers in place during operation.
11. Never allow anyone to stand directly in front of or near outfeed end of machine.
12. Turn motor OFF, disconnect power, and make sure machine has come to complete
stop before changing sandpaper or servicing.
13. Do not wear loose clothing, gloves, jewelry, or other articles that can get entangled.
Tie back long hair and roll up sleeves.
14. Do not expose to rain or use in wet locations.
15. Do not operate under influence of drugs or alcohol, or if tired.
16. Prevent unauthorized use by children or untrained users; restrict access or disable
machine when unattended.
Front Sanding Motor: 15 HP, 220V, 36.7A, 3-Ph, 60 Hz
Rear Sanding Motor: 15 HP, 220V, 36.7A, 3-Ph, 60 Hz
Feed Motor: 2 HP, 220V, 6A, 3-Ph, 60 Hz
Table Elevation Motor: 1/4 HP, 220V, 1.2A, 3-Ph, 60 Hz
Full-Load Current Rating: 79.4A @ 220V, 39.9A @ 440V
Drum Surface Speed: 3600 FPM (Front), 2800 FPM (Rear)
Feed Rate: 7–68 FPM
Maximum Board Width: 36-1/2"
Maximum Board Thickness: 6"
Minimum Board Thickness: 3/16"
Minimum Board Length: 12"
Sanding Belt Size: 37" x 75"
Infeed Sanding Drum Size: 8.7" (Front), 5" (Rear)
Outfeed Sanding Drum Diameter: 5"
Required Air Pressure: 57–75 PSI
Weight: 3417 lbs.
Specifications
WARNING!
Date
Mfd. for Grizzly in Taiwan
SN
MODEL G0866
37" SUPER INDUSTRIAL DOUBLE-HEAD
WIDE-BELT SANDER
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
G0866 Machine Labels B
(12.20.18)
• Scale= 1:1
(unless otherwise noted)
WARNING!
KEEP DOOR
CLOSED WHILE
OPERATING!
PINCH HAZARD!
Keep hands away from pinch
points during operation.
Severe injury could occur if
hands get caught between
feed belt and stock or
between pressure roller and
stock.
KICKBACK HAZARD!
Do not insert more than
one board at a time. Stock
may be ejected at a high
rate of speed from this
machine.
This machine is prewired for 220V
operation. To operate at 440V,
follow critical voltage conversion
instructions in the user manual
included with this machine.
Failure to follow these instructions
will damage the machine and void
the warranty!
220 VOLT
Position of this plate is factory set to allow maximum safe sanding depth. DO
NOT adjust or remove. Failure to do so could seriously damage machine.
NOTICE
grizzly.com
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
• Labels MUST be made of
chemical-resistant material
DANGER
PANTONE 485 C or RAL 3001
COLOR CODES
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
NOTICE PANTONE 3005 C or RAL 5005
GRIZZLY GREEN
PANTONE 568C
220
V
:
440
V
:
10
A
33
A
36
A
SAFE DAMAGE CAUTION
30
A
68
A
72
A
SAFE DAMAGE CAUTION
Model: G0866
AMPERAGE LOAD CHART
NOTICE
Press and hold this button for
10 seconds to switch display
between metric and SAE units.
G0866 Machine Labels C
(12.20.18)
• Scale= 1:1 (unless otherwise noted)
• Labels MUST be made of chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
REMOVE SANDING BELT(S) AND
CLEAN RUST PREVENTATIVE
FROM UPPER DRUM(S)
BEFORE USING THIS
MACHINE.
DANGER
PANTONE 485 C or RAL 3001
CAUTION
PANTONE 109 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
COLOR CODES
GRIZZLY GREEN PANTONE 568C