Grizzly G0853, Owner'S Manual

Page: 136 / 140

-134-
Model G0853 (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
Labels & Cosmetics (Front)
grizzly.com
Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.
If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.
AMPUTATION
HAZARD!
Always keep
fingers and
hands away from
moving blade.
A blade splitter or
riving knife MUST
be used with this
guard to reduce
risk of kickback!
WARNING! WARNING! WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
WARNING!
G0853
Only trained personnel
should operate this
machine. If safe operation
procedures are not clearly
understood, get additional
training before using.
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
WARNING!
KICKBACK INJURY
HAZARD!
DO NOT stand
directly in front of
or behind blade
path.
WARNING!
MODEL G0853
14" SLIDING TABLE SAW
WITH DIGITAL FENCE
Specifications
WARNING!
Max Length of Cut w/Cross Cut Fence: 126"
Max Width of Cut w/Cross Cut Fence: 126"
Max Width of Cut w/Rip Fence: 51-1/2"
Max Depth of Cut: 4"
Weight: 1890 lbs.
Date
S/N
Mfd. for Grizzly in Taiwan
To reduce risk of serious injury when using this machine:
1. Read and understand owner’s manual before operating.
2. Never touch moving blade and always keep hands out of cutting path.
3. Always wear approved eye protection and respirator.
4. Properly ground machine—connect to permanently grounded metal wiring
system or an equipment-grounding conductor.
5. Use blade guard and riving knife for all cuts.
6. Only use blades meeting size/speed requirements for this saw.
7. Ensure riving knife, fence, and scoring blade are properly adjusted and parallel
with main blade.
8. Ensure machine is stable.
9. Never reach behind or over blade while it is moving.
10. Use a push stick when required and whenever possible.
11. Know what causes “kickback” and how to prevent it.
12. Never remove jammed/cutoff workpiece when blade is moving!
13. Make sure blade is stopped before adjusting blade height/tilt.
14. Do not perform any operation freehand.
15. Disconnect power before changing blades or servicing saw.
16. Plan cuts so workpieces always remain supported.
17. Do not wear loose clothing, gloves, jewelry, or other items that can get entangled. Tie
back long hair and roll up long sleeves.
18. Do not expose to rain or operate in a wet environment.
19. Prevent unauthorized use by children or untrained users; restrict access or
disable machine when unattended.
Main Motor: 10 HP, 220V/440V, 3-Ph, 60 Hz
Scoring Motor: 1 HP, 220V/440V, 3-Ph, 60 Hz
Full-Load: 29.2A at 220V, 14.6A at 440V
Pre-Wired Voltage: 220V
Main Blade Size: 14"
Main Blade Arbor Size: 1"
Main Blade Speed: 3000, 4000, 5000 RPM
Scoring Blade Size: 120mm (4-3/4")
Scoring Blade Arbor Size: 20mm
Scoring Blade Speed: 8000 RPM
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
REF PART # DESCRIPTION REF PART # DESCRIPTION
1901 P08531901 MODEL NUMBER LABEL 1906 P08531906 DISCONNECT POWER LABEL
1902 P08531902 BLADE GUARD WARNING LABEL 1907 P08531907 KICKBACK WARNING LABEL
1903 P08531903 SAFETY NOTICE LABEL 1908 P08531908 GRIZZLY.COM LABEL
1904 P08531904 GLASSES/RESPIRATOR LABEL 1909 P08531909 MACHINE ID LABEL
1905 P08531905 READ MANUAL LABEL 1910 P08531910 GRIZZLY NAMEPLATE–LARGE