Grizzly G0602 Owner'S Manual Download Page 32 | Manualshive

Page: 32 / 100

background image

-26-

Model G0602/G0752 (Mfd. Since 03/17)

This lathe ships with the 3-jaw chuck installed.
This is a scroll-type chuck where all three jaws
move in unison when the chuck key is used.

The included 4-jaw chuck features independent
jaws, which are used for square or unevenly-
shaped stock, and to mount work that needs to be
adjusted to near zero total indicated runout.

If  neither  chuck  can  hold  your  workpiece,  the
cast iron faceplate has slots for T-bolts that hold
standard or custom clamping hardware. With the
correct  clamping  hardware,  a  faceplate  offers  a
wide  range  of  uses,  including  machining  non-
concentric  workpieces,  straight  turning  between
centers, off-center turning, and boring.

This lathe is equipped with a threaded spindle
nose. With this type of spindle, a chuck or face-
plate is screwed directly onto the spindle nose.

Never use spindle speeds faster than the

chuck RPM rating or the safe limits of

your workpiece. Excessive spindle speeds

greatly increase the risk of the workpiece or

chuck being thrown from the machine with

deadly force!

Chuck & Faceplate

Mounting

Installation &

Removal Devices

Pre-Threaded Hole
for Lifting Eye

Way Slot

Jaw Slot

Plywood & 2x4
Chuck Cradle

Plywood Chuck Cradle
(Straight Cuts)

Plywood Chuck Cradle
(Curved Cuts)

Fabricated Steel
Lifting Hook

Solid Block
Chuck Cradle

Plywood Protection
Plate for Chucks
Installed by Hand

MEDIUM-SIZE, HEAVY CHUCKS

LARGE, VERY HEAVY CHUCKS

SMALL, LIGHTWEIGHT CHUCKS

Figure 20. Examples of common devices used

during chuck installation and removal.

A dropped chuck can cause amputation,

serious crushing injuries, or property dam-

age. Always use a support or protective

device to reduce this risk when installing or

removing a chuck.

Loose hair, clothing, or

jewelry could get caught

in machinery and cause

serious personal injury.

Keep these items away

from moving parts at all

times to reduce this risk.

Because chucks are heavy and often awkward to
hold,  some  kind  of  support  or  protective  device
should be used during installation or removal. The
weight  and  size  of  the  chuck  will  determine  the
appropriate  device  to  use  (refer  to  the  following
figure for examples).

«
...
30
31
32
33
34
...
»

Summary of Contents for G0602





































































































Reviews:

No comments

Related manuals for G0602

Brand: Axminster Pages: 20

Brand: LittleMachineShop.com Pages: 47

Brand: Grizzly Pages: 116

Brand: Huvema Pages: 14

Brand: Huvema Pages: 17

HU 410 x 800 VAC TOPLINE

Brand: Huvema Pages: 30

HU 480 X 2200 VAC TOPLINE

Brand: Huvema Pages: 76

Brand: CNC-Step Pages: 24

Brand: CNC-Step Pages: 74

Brand: Flott Pages: 19

Brand: Grizzly Pages: 4

TOOLROOM KC-1640ML

Brand: King Industrial Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands