GREER COMPANY
GREER COMPANY
GREER COMPANY
GREER COMPANY
Crane Systems
Crane Systems
Crane Systems
Crane Systems
GREER COMPANY 1918 EAST GLENWOOD PLACE SANTA ANA, CALIFORNIA 92705
PN W453201A 08/10/00
MicroGuard
®
434/500 CALIBRATION MANUAL
TEL: 714) 259-9702 FAX: 714) 259-7626
20
OF
39
MAIN BOOM
MAIN BOOM
MAIN BOOM
MAIN BOOM RADIUS/MOMENT
RADIUS/MOMENT
RADIUS/MOMENT
RADIUS/MOMENT
A. EXIT THE CALIBRATION MODE AND PRESS THE
CRANE SETUP
BUTTON AT THE BOTTOM OF THE
DISPLAY SCREEN. SELECT
FULLY EXTENDED OUTRIGGERS, MAIN BOOM, NO ATTACHMENTS, OR A
STOWED ATTACHMENT.
B. FULLY RETRACT THE BOOM. THE BOOM ANGLE SHOULD BE 5°.
C. DETERMINE THE WEIGHT OF THE HOOK BLOCK IN USE. MEASURE THE RADIUS FROM THE CENTERLINE
OF ROTATION TO THE CENTER OF THE HOOK OR LINE (IF SINGLE PART).
D. CALIBRATE THE RADIUS AND MOMENT OF THE MAIN BOOM AS SHOWN BELOW.
.
COMMAND 05 MAIN BOOM RADIUS
COMMAND 05 MAIN BOOM RADIUS
COMMAND 05 MAIN BOOM RADIUS
COMMAND 05 MAIN BOOM RADIUS/MOMENT
/MOMENT
/MOMENT
/MOMENT
FIRST LENGTH
FIRST LENGTH
FIRST LENGTH
FIRST LENGTH
RAISE THE HOOK BLOCK
RAISE THE HOOK BLOCK
RAISE THE HOOK BLOCK
RAISE THE HOOK BLOCK CLOSE TO THE TWO
CLOSE TO THE TWO
CLOSE TO THE TWO
CLOSE TO THE TWO----BL
BL
BL
BLOCK WEIGHT
OCK WEIGHT
OCK WEIGHT
OCK WEIGHT
TO ELIMINATE ROPE WE
TO ELIMINATE ROPE WE
TO ELIMINATE ROPE WE
TO ELIMINATE ROPE WEIGHT.
IGHT.
IGHT.
IGHT.
0
.
ENTER THE CALIBRATION MODE AND CALIBRATION CODE, IF NOT ALREADY DONE. SEE PAGE 5.
1.
CHOOSE
MENU UP OR MENU DOWN AND GO TO 05 RADIUS/MOM.
...............................................
2
2
2
2
OR
OR
OR
OR
3
3
3
3
2
. START 05 RADIUS/MOM.
...................................................................................................................................
1
11
1
3.
USE THE NUMBER ENTRY ROUTINE (PAGE 6) TO ENTER WEIGHT OF HOOK (TARE LOAD).
4.
STORE LOW ANGLE DATA.
................................................................................................................................
1
11
1
5.
USE THE NUMBER ENTRY ROUTINE (PAGE 6) TO ENTER THE CURRENT RADIUS
THE DISPLAY WILL READ: BAS. 0 (D ).
RAISE THE RETRACTED
RAISE THE RETRACTED
RAISE THE RETRACTED
RAISE THE RETRACTED BOOM TO AN ANGLE BET
BOOM TO AN ANGLE BET
BOOM TO AN ANGLE BET
BOOM TO AN ANGLE BETWEEN 60
WEEN 60
WEEN 60
WEEN 60
°°°°
AND 65°
AND 65°
AND 65°
AND 65°
AND MEASURE THE NEW
AND MEASURE THE NEW
AND MEASURE THE NEW
AND MEASURE THE NEW RADIUS.
RADIUS.
RADIUS.
RADIUS.
6.
STORE THE HIGH ANGLE DATA.
.......................................................................................................................
1
11
1
7.
USE THE NUMBER ENTRY ROUTINE TO ENTER THE NEW RADIUS.
THE DISPLAY WILL READ: BAS. 0 (D U).
8.
START THE MOMENT CALIBRATION AT THE CURRENT LENGTH.
..............................................................
1
11
1
9.
CONFIRM OR ABORT THE CALIBRATION.
..........................................................................
1
YES
/3
33
3
ABORT
REVIEW THE SAMPLE
REVIEW THE SAMPLE
REVIEW THE SAMPLE
REVIEW THE SAMPLE DISPLAY SCREEN ON PAGE 4
DISPLAY SCREEN ON PAGE 4
DISPLAY SCREEN ON PAGE 4
DISPLAY SCREEN ON PAGE 4.
Use the designated arrow key (
1, 2, 3, 4, or 6
1, 2, 3, 4, or 6
1, 2, 3, 4, or 6
1, 2, 3, 4, or 6
) appearing to the right of each step
when ENTERING or EXITING a COMMAND
and to CHOOSE, START, CONFIRM, ABORT, RESET, or ENTER an action.
