background image

Ceiling Exhaust Fans

11

®

Typical Installation

The ducting from this fan to the outside of the building has a strong effect on the airflow, noise and energy use of 
the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with 
smaller ducts than recommended. Insulation around 
the ducts can reduce energy loss and inhibit mold 
growth. Fans installed with existing ducts may not 
achieve their rated airflow.
Rigid metal duct is recommended for optimal fan 
performance. 
Ensure duct joints and exterior penetrations are 
sealed with caulk or other similar material to create 
an air-tight path and to minimize building heat loss 
and gain and reduce the potential for condensation.
Place/wrap insulation around duct and/or fan to in 
order to minimize possible condensation buildup 
within the duct, as well as minimize building heat 
loss and gain.

*Purchase separately.

INSULATION*

(Place around and over Fan Housing.) 

ROOF CAP*

(with built-in damper)

FAN HOUSING

POWER CABLE*

ROUND DUCT*

ROUND

ELBOWS*

Seal gaps 
around Housing.

Seal duct joints
with tape.

OR

Keep duct 
runs short.

WALL CAP*

 

(with built-in damper)

Summary of Contents for SP-AP0511W













Reviews: