Please read the instructions fully before
attempting installation.
IMPORTANT
This unit should be installed to current
IET wiring regulations if in doubt
consult a qualified electrician.
• Timer must not be mounted on a
flammable surface.
• Ensure that the timer does not come into
contact with any combustible materials
such as towels or bedding.
• Ensure at least a 300mm air space is
allowed around the timer.
• Prepare cable ends for connection to
terminals.
• Remove the 2 screws holding the
timeswitch cover to the backplate.
Remove cover leaving the timeswitch
hanging loose by its connection wires
to the backplate.
DO NOT INTERFERE
WITH THESE FIXED CONNECTIONS
.
Installation/ Operating
Instructions for 7 Day
Electronic Socket Box Timer
- T105A-C
INSTALLATION
WIRING
2. Press Y to enter function setup. (Note:
if another button is not pressed within 10
seconds the display will revert to the
normal screen).
3. Use the + or - button to scroll to the clock
icon (flashing) and press Y to enter the
current time setting mode (hours
flashing).
4. If you keep the + or - buttons pressed for
more than 3 seconds, the display will
enter fast scroll mode.
5. Use the + or - button to adjust the hours
and press Y to confirm, minutes will flash.
6. Use the + or - button to adjust the
minutes and press Y to confirm, day will
flash.
7. Use the + or - button to adjust the day
and press N to exit.
1. Press the R button to reset the timer to its
default settings, activate using a pencil
or simular pointed instrument. (pressing
R will delete all stored programmes).
1. There are 24 ON/OFF programmes
available.
2. Press the Y button twice to enter the
programming setting mode.(Note: if
another button is not pressed within 10
seconds the display will revert to the
normal screen).
3. Default is programme 01 ON, this can be
changed if required by pr or -
button to scroll through the 24 ON/OFF
programmes as required, pressing the Y
will confirm the programme.
4. Press the Y button to confirm programme
01 ON, hours will flash.
5. Use the + or - button to adjust the hours
and press Y to confirm, minutes will flash.
6. Use the + or - button to adjust the
minutes and press Y to confirm, days will
flash.
7. Apart from individual days of the week,
the following day combinations of
multiple day blocks can be selected by
pressing the + or - buttons.
• Monday to Sunday
• Monday to Friday
• Saturday to Sunday
• Monday to Saturday
• Wed Friday
• T Th Saturday
• T Wednesday
• Th Saturday
8. Select day or day block as required and
press the Y button to confirm.
9. Press the + button, this will select the
programme 01 OFF, press Y to confirm.
10.Follow 4 to 7 above to set the 01 OFF
programme (day or day block must be
the same as programme ON).
11.If no more programmes are required,
press the N button to exit.
12.If more programmes are required follow
3 above.
13.To cancel a programme once set, press
and hold the N button for more than 3
seconds when the desired programme
number is flashing i.e. to cancel
programme 01 ON, press the Y button
twice and hold the N button down for
more than 3 seconds to delete. Pressing
the + button again will select 01 OFF.
14.Repeat 13 to delete 01 OFF. This
procedure can be repeated to delete
any of the 24 programmes.
CURRENT TIME AND
DAY SETTING
PROGRAMMING THE
SWITCHING TIMES
16AMP(2)
• Connect all earth wires to earthing point
in wall box.
• Offer up the backplate to the wall box
and connect the wiring as shown in
diagram below.
• When the wiring is complete screw the
backplate to the fitted wall box using
3.5mm screws.
• Push the timeswitch back in to its seating
on the backplate, taking care that all the
wires are tucked in. Fit the cover and
tighten the two screws.
IMPORTANT:
Ensure all Terminal screws are fully tightened.
