Gree GRS-1.5/D150ANbA-K Service Manual Download

Page: 57 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

2 Troubleshooting

2.1 E1 High Pressure Protection

Fault code:

Applicable mode: HOTWATER; SAVE; PRESET; NIGHT

Fault judgment condition and method: E1 is displayed on the wired controller. The troubleshooting

method is shown in the flowchart below.

Possible cause: 1) Poor connection of the water tank temperature sensor; 2) Loose pressure switch

cable; 3) Pressure switch fault; 4) Mainboard fault

Troubleshooting:

E1 high pressure

protection

Check whether the

thermo-bulb of the water

tank is properly installed.

Check whether the

pressure switch is

abnormal.

Check whether the

pressure switch is

properly connected.

Replace the mainboard.

Installed the thermo-bulb

properly.

Re-connect the cable for

the pressure switch.

Replace the pressure

switch.

Summary of Contents for GRS-1.5/D150ANbA-K


















































































Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands

Gree GRS-1.5/D150ANbA-K, Service Manual

Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands