background image

Multi Variable Air Conditioners Cassette Type Indoor Unit

 

Unit:mm 

Model 

GMV-ND28~50T/A-T 

220 

GMV-ND56~80T/A-T 

270 

GMV-ND90~140T/A-T 

350 

GMV-ND160T/A-T 

310 

NOTES! 

  The unit shall be installed in accordance with national standards or local regulations. 

  Only qualified personnel can carry out installation work, please contact with local dealer before 

installation. 

  Make sure all the installation work completed before energizing. 

  The appliances are not accessible to general public. 

3.3 Requirements of Communication Wire Selection 

NOTE!

 

If air conditioner used under strong electronic-magnetic interference circumstance, STP 

(shielded twisted pair) communication cable must be adopted.

 

3.3.1 Selection of Communication Wire Between Indoor Unit and Wired Controller 

 

Fig.3.3.1 

Wire type 

Total length of 

communication wire between 

indoor unit and wired 

controller (m) 

Wire diameter 

(mm²) 

Wire standard 

Remark 

Light/normal PVC 

hose 

L

250 

2×0.75 

~2×1.25 

IEC 

60227-5 

1. Total length of communication 

line can't exceed 250m. 

2. The cord shall be Circular cord 

(the cores shall be twisted 
together). 

3. If unit is installed in places with 

intense magnetic field or strong 
interference, it is necessary to 
use shielded wire. 

 
 
 
 
 
 

Summary of Contents for GMV-ND100T/A-T




























Reviews: