background image

52

Duct Type Split Air Conditioner
Service Manual

2 FLOW CHART OF TROUBLESHOOTING

2.1 High Pressure Protection

Compressor High Pressure  

Protection

Check if the capacity output of the outdoor 
unit is the same as that of the indoor unit?

Check if the swing blades are completely 
open?

Check if the fans for the indoor and outdoor 
units are working?

Check if the ventilation 
for the indoor and outdoor units is smooth?

Check if the outdoor unit
if the panel has been sealed properly?

Inspect if the gas and liquid 
valves are open? 

Inspect if the operational modes of the 
indoor unit are set correctly?

Use pressure gauge to measure the

  

pressure if it I real high pressure?

the system pipes are jammed

Check if the filters or heat exchange fins for 
the indoor and outdoor units are 
contaminated or jammed?

Particularly check the inlets and outlets of the main pipes 
that are connected with the indoor unit and the electronic 
expansion valve of the outdoor unit.Replace the expansion 
valve and the dryer filter

.

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Measure if the pressure switch 
if it is iproper condition?

refer to mode conflict

measure the fan motor 
and the signal input

remove obstacles

install the panel

completely open the valve 

refer to maintenance

refer to capacity code

Check the swing motor 
and the signal input

No

No

No

No

No

No

No

No

No

replace the pressure 
switch

replace main board of the 
outdoor unit

No

Yes

Summary of Contents for FG20/BNa-M




















































































Reviews: