Gree CM100N1320 Service Manual Download Page 131

Page: 131 / 276

GREE

GMV5 INDOOR UNIT SERVICE MANUAL

126

probably not be dealt with on time because of the inconvenience of the business contact.



It should be guided under the professional personnel when the air conditioner unit is moved to

other place.



Installation of the unit must be in accordance with National Electric Codes and local regulations.



Improper installation will affect unit’s performance, so do not install the unit by yourself. Please

contact local dealer to arrange professional technicians for the installation.



Do not connect power until all installation work is finished.



The height of ex-factory supporter is 120mm. If user wants to increase or decrease unit

installation height, please purchase the supporter of different height. Other height of supporter

is 80mm, or 160mm.



Default height of inlet grille is 120mm. If the supporter of 80mm or 160mm high is selected,

please change the height of inlet grille to 80mm or 160mm accordingly.

3.15.4 Selection of air switch and power cord

Model

Power Cord Size

Air Switch apacity

(A)

Minimum Sectional

Area of Ground Wire

(mm

/AWG)

Minimum Sectional

Area of Power Cord

(mm

/AWG)

GMV-ND22ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND28ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND36ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND45ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND56ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND63ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

GMV-ND71ZA/A-T

220-240V/50Hz
208-230V/60Hz

1.0/AWG18

4 Installation of drain pipe

4.1 Precautions When Doing the Piping Work

(1) It is not allowed to connect the condensate drain pipe into waste pipe or other pipelines which

are likely to produce corrosive or peculiar smell to prevent the smell from entering indoors or

corrupt the unit.

(2) It is not allowed to connect the condensate drain pipe into rain pipe to prevent rain water from

pouring in and cause property loss or personal injury.

(3) Condensate drain pipe should be connected into special drain system for air conditioner.

Summary of Contents for CM100N1320





















































































































































































































































































Search results

Summary of Contents for CM100N1320

Reviews:

Related manuals for CM100N1320

Brands by name

Popular brands

Gree CM100N1320, Service Manual

Search results

Summary of Contents for CM100N1320

Reviews:

Related manuals for CM100N1320

Brands by name

Popular brands