background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability
exceed the original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

READ THROUGH THIS  MANUAL  BEFORE
STARTING CONSTRUCTION. IT CONTAINS
IMPORTANT WARNINGS AND INSTRUCTIONS
CONCERNING THE ASSEMBLY AND USE OF
THIS MODEL.

GPMZ0232 for GPMA1215  V1.0

© Copyright 2001

1610 Interstate Drive  Champaign, IL 61822

(217) 398-8970, Ext 2

[email protected]

INSTRUCTION MANUAL

TM

Wingspan: 61.5 in. [1562mm]
Wing area: 1076 sq. in. [69.5 sq dm]
Weight: 6 lbs [2720g]
Wing loading: 9.6 oz./sq. ft. [29.3 g/sq dm]
Length: 49 in. [1245mm]
Radio: 4-Channel (5 Servos)
Engine: .35 to .46 two-stroke, .52 four-stroke [5.75 to 7.5cc two-stroke, 8.5cc four-stroke]

Summary of Contents for Slow Poke Sport .40





















Reviews: