4
The following is the list of hardware and accessories
required to finish the Little Toni. Order numbers are provided
in parentheses.
❏
R/C foam rubber (1/4" [6mm] - HCAQ1000, or 1/2"
[13mm] - HCAQ1050)
❏
William’s Brother’s #626 1/4-scale sportsman pilot
(WBRQ2626)
❏
1/2 oz. [15g] Thin Pro
™
CA (GPMR6001)
❏
1 oz. [30g] Medium Pro CA+ (GPMR6008)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32" [2.4mm],
1/8" [3.2mm], 3/16" [4.8mm], 9/64" [3.6mm]
❏
8-32 tap and drill set (GPMR8103)
❏
#1 Hobby knife (HCAR0105)
❏
#11 blades (5-pack, HCAR0211)
❏
Medium T-pins (100, HCAR5150)
❏
Top Flite
®
MonoKote
®
sealing iron (TOPR2100)
❏
CA applicator tips (HCAR3780)
❏
Propeller (as recommended by the engine
manufacturer)
Here is a list of optional tools mentioned in the manual that
will help you build the Little Toni.
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
R/C-56 canopy glue (JOZR5007)
❏
CA debonder (GPMR6039)
❏
Epoxy brushes (6, GPMR8060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
36" metal ruler (HCAR0475)
❏
Curved-tip canopy scissors for trimming plastic parts
(HCAR0667)
❏
Robart Super Stand II (ROBP1402)
❏
18" x 24" [460 x 610mm] Builder’s Cutting Mat
(HCAR0455)
❏
Hobbico
®
Duster
™
can of compressed air (HCAR5500)
❏
Masking tape (TOPR8018)
❏
Threadlocker thread locking cement (GPMR6060)
❏
Denatured alcohol (for epoxy clean up)
❏
Switch & Charge Jack Mounting Set (GPMM1000)
❏
Rotary tool such as Dremel
®
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Servo horn drill (HCAR0698)
❏
Dead Center
™
Engine Mount Hole Locator
(GPMR8130)
❏
AccuThrow
™
Deflection Gauge (GPMR2405)
❏
CG Machine
™
(GPMR2400)
❏
Precision Magnetic Prop Balancer
™
(TOPQ5700)
There are two types of screws used in this kit:
Sheet metal screws are designated by a number and a length.
For example #6 x 3/4"
This is a number six screw that is 3/4" long.
Machine screws are designated by a number, threads per
inch, and a length.
For example 4-40 x 3/4"
This is a number four screw that is 3/4" long with forty
threads per inch.
·
When you see the term
test fit in the instructions, it
means that you should first position the part on the
assembly without using any glue, then slightly modify
or
custom fit the part as necessary for the best fit.
·
Whenever the term
glue is written you should rely upon
your experience to decide what type of glue to use. When
a specific type of adhesive works best for that step, the
instructions will make a recommendation.
·
Whenever just
epoxy is specified you may use either 30-
minute (or 45-minute) epoxy
or 6-minute epoxy. When
30-minute epoxy is specified it is highly recommended
that you use only 30-minute (or 45-minute) epoxy,
because you will need the working time and/or the
additional strength.
·
Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following
steps to get another view of the same parts.
·
The Little Toni ARF is factory-covered with Top Flite
®
MonoKote
®
film. Should repairs ever be required,
MonoKote can be patched with additional MonoKote
purchased separately. MonoKote is packaged in six-foot
rolls, but some hobby shops also sell it by the foot. If only
a small piece of MonoKote is needed for a minor patch,
perhaps a fellow modeler would give you some.
MonoKote is applied with a model airplane covering iron,
but in an emergency a regular iron could be used. A roll
of MonoKote includes full instructions for application.
Following are the colors used on this model and order
numbers for six foot rolls.
True Red (TOPQ0227)
(continued on page 6)
Important Building Notes
Optional Supplies and Tools
Additional Items Required
Summary of Contents for Little Toni ARF
Page 28: ...28 ...
