manualshive.com logo in svg

GREAT PLAINS SS0300, Original Instructions Manual

Share
Download
GREAT PLAINS SS0300 Original Instructions Manual Download Page 10

Great Plains

 | 596-224M | 3/22/19

Table of Contents

Index

6

SS0300

Table of Contents

Index

Important Safety Information

Safety At All Times

Thoroughly read and understand the instructions in this

manual before operation. Read all instructions noted on

the safety decals.

Be familiar with all product functions.

Operate machinery from the driver’s seat only.

Do not leave product unattended with tractor engine
running.

Do not stand between the tractor and implement, or

implement and nurse tank during hitching.

Keep hands, feet and clothing away from power-driven

parts.

Wear snug-fitting clothing to avoid entanglement with
moving parts.

Watch out for wires, trees, etc., when folding and raising

product. Make sure all persons are clear of working area.

Accident Prevention

In addition to the Operating Instructions, it is important

to observe the accident prevention regulations specified

by agricultural trade associations. It is the Operator’s
responsibility to ensure that all other persons are

excluded from danger zones surrounding or on the

machine during its operation.

Summary of Contents for SS0300



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands