manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 87

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

83

2019-03-11

Table of Contents

Index

407-502M

Short-Term Parking

1. Conclude application per “

Stopping Application

” on

page 77.

2. Unhitch nurse tank per “

Final Nurse Tank Unhitch

”

on page 80.

3. Choose an applicator parking location with level firm

ground. Do not unhitch on a steep slope.

4. Recover emergency shutoff rope from tractor.

Store on applicator.

5. Fully raise applicator (page 50).
6. Fold applicator (page 59).
7. Depending on hitch type: 

Engage center section and lift-assist transport locks

(page 45), and/or

swing down parking stands (page 36) and/or

install jack stand on tongue (page 30).

8. Lower fertilizer applicator onto locks/stands. On

pull-type, use parking jack to neutralize tongue

weight at tractor hitch.

9. Set hydraulic circuits to neutral.
10. Disconnect hydraulic lines. Secure them so that they

do not touch the ground.

11. Disconnect electrical cables, capping where

provisioned.

12. Disconnect any safety chain. Unhitch. Restart tractor

and pull away from fertilizer applicator.

Long-Term Storage

1. Conclude application per “

Stopping Application

” on

page 77.

2. Unhitch nurse tank per “

Final Nurse Tank Unhitch

”

on page 80.

3. Choose an applicator parking location with level firm

ground. Do not unhitch on a steep slope.

4. Recover emergency shutoff rope from tractor.

Store on applicator.

5. Fully raise applicator (page 50).
6. Clean fertilizer applicator of mud, dirt, excess oil and

grease.

7. Lubricate all points listed in Maintenance.
8. Apply grease to exposed cylinder rods to prevent

rust.

9. Inspect fertilizer applicator for worn or damaged

parts. Make repairs and service during off season.

10. Use spray paint to cover scratches, chips, and worn

areas on the fertilizer applicator to protect the metal.

11. Fold applicator.
12. Cover fertilizer applicator with a tarp if stored

outside.

Ending Application Checklist

Page

1

Suspend operations as at left, then…

76

2

Put on your goggles and gloves

-

3

Close nurse tank withdrawal valve

77

4

Re-enter cab. Turn MASTER switch ON

-

5

Resume field application.

Raise flow rate to maximum.

77

6

Continue application until both cooler and flow 

divider pressures are zero.

-

7

Turn into wind.

-

8

Raise applicator and stop.

50

9

Set MASTER switch off.

-

10

Wait one minute.

-

11

Turn left (wind from right). Stop.

-

12

Open all bleed valves.

77

13

Close all line valves.

77

14

Wait one hour.

77

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands