GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 128

Page: 128 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Maintenance and Lubrication

124

Metering System Maintenance

Fully discharge system before performing any

maintenance. See “

System Discharge

” on page 115.

If any system components are removed from plumbing,

when replacing or re-installing them, use only a pipe

sealant specified for use with anhydrous ammonia, such

as RectorSeal #5.

Strainer

Maintenance

Clean magnets every 4 to 5 tank loads. Check strainer

screen at that time.
Ceramic magnets scavenge ferrous metal debris from

the flow, preventing this material from contaminating the

magnets in the flow meter

The 20 mesh screen filters out non-magnetic particles

that could interfere with both accurate flow metering and

flow control. If the screen cannot be cleaned, or is

damaged, the replacement is Raven part number

339-9000-032.

Cooler

Maintenance

Manual 016-0159-403, the Raven AccuFlow™ Operator

manual, has specific recommendations for seasonal

cooler storage, cleaning, and preserving the interior of

the supercooler.

Cooler Hydrostatic Relief Valve

This is a limited life part (page 122). Check for expiration

whenever servicing the cooler.

Flow Meter

Maintenance

If flow meter readings are irregular, or consistently low

relative to the amount of NH

known to have flowed from

the tanks, remove the meter for cleaning and inspection.

Refer to 016-0159-403, the Raven AccuFlow™ Operator

manual, for details.

Suffocation, Blinding, Burning, Freezing, Disabling and
Disfigurement Hazards:

Do not perform maintenance with anhydrous ammonia in the

system. Fully discharge the system of NH

liquid and vapor

before working on the applicator.

Tank Failure Early Warning:

An excessive build-up on the magnets suggests that or more
more nurse tanks, employed since the most recent magnet

cleaning, is/are deteriorating internally. Notify the tank cart

provider. If you own the tanks used, take steps to identify the
failing tank.

A19

A25

Equipment Damage Risk:

Periodic cleaning is essential if NH

additives have been used,

such as Dow Chemical N-Serve or Amoco ACA.

A21

A23

A25

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands