manualshive.com logo in svg

GREAT PLAINS CTA4000, Pre-Delivery Instructions, Page: 14 / 38

Share
Download
GREAT PLAINS CTA4000 Pre-Delivery Instructions Download Page 14

10 CTA4000 & CTA4000HD

Table of Contents Appendix

Great Plains Manufacturing, Inc.

160

-

037Q

Table of Contents Appendix

2019

-

10

-

17

Mount Valve / Plumb Wings

Refer to Figure 8

1. Unstrap valve block  from center section. Uncoil 

and stretch attached hoses out to left wing section. 

U

-

bolt valve block to top frame member . 

Note: Mount valve block  as far left as hoses will allow. 

If the valve block is mounted too far right, it may 

interfere with cart hopper during folding.

2. Connect hoses from center section to tee fittings on 

wings. On left wing, connect hoses from valve block 

to tee fittings.

Note: The SAE O

-

Ring Boss (ORB) and JIC 37

 

flare

-

type hose connections do not require sealant 

or high torque for a good seal.

3. Route hydraulic hoses under hose clamps  on 

frame.

4. Carefully check all hoses to make sure none will be 

damaged by implement operation. Reroute hoses or 

use cable ties to keep hoses in a safe place.

3

2

1

3

3

3

U

D

F

B

L

R

Figure 8

Hose Routing and Valve

17178

1

2

1

3

Summary of Contents for CTA4000







































Reviews:

No comments