manualshive.com logo in svg

GREAT PLAINS 3S-4000, Operator'S Manual

Share
Download
GREAT PLAINS 3S-4000 Operator'S Manual Download Page 52

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Operating Instructions

48

Acremeter Operation

The acremeter

a

 counts shaft rotations whenever the

shaft is rotating - normally this is only with the drill
lowered and in motion. The meter is programmed to
display rotations as acres or hectares, when using all
rows, factory-specified tires and tire inflations.

Unusual conditions and/or non-standard row
spacings can cause the acremeter tally to vary
somewhat from actual acres planted.

Refer to Figure 46

Acremeters supplied with model 3S-4000, 3S-4000F,
3S-4000HD, 3S-4000HDF drills have varied over time.
For operational details (modes, resets, calibration), see
the manual supplied with the acremeter:

Field Operations

This section presumes that all pre-operation checks have
been made on both tractor and drill, and drill is loaded
with seed and any treatments.

Final Field Checklist

Planting Sequence

1.

Lower drill openers at initial seeding point.

2.

Pull forward and begin planting.

3.

Raise drill for turns (meters stop automatically).

a. An electronic acremeter is available as an upgrade for older drills having a mechanical acremeter.

Meter Style and Manual

 194-074M

 152-314M

 152-325M

 194-209M

?

Drill hitched, chained and unfolded. See page 19 and 
page 34.

?

Set seed and fertilizer drives per charts and calibration. See 
Seed Rate Manual.

?

Set drill selector valves (if present) to Markers and Opener 
Lift. See page 45 and page 46.

?

If installed, Shaft Monitor power ON.

?

If installed, Point Row Control module ON, and set for either 
ALL or SECTION CONTROL.

Figure 46

Acremeters

34776
34937
27378
36275

1

2

3

4

1

3

2

4

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands