manualshive.com logo in svg

GREAT PLAINS 3S-4000, Operator'S Manual

Share
Download
GREAT PLAINS 3S-4000 Operator'S Manual Download Page 37

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Operating Instructions

33

2018-06-19

Table of Contents

Index

195-442M

Transport Lower

1.

Park tractor and drill on level ground with tractor
transmission in Park. Be aware of clearance needed
to unfold drill.

2.

If the Two Outlet conversion kit is installed, confirm
that the selector valve, located near the hitch, is set
for Transport Lift operations. See “

Lift Selector

Valve Operation

” on page 46.

3.

Slowly extended the Transport Lift circuit lever until
all three Transport Lift circuit cylinders are fully
extended (2 at transport wheels; 1 at transport hooks
on tongue). Set circuit lever to off (not neutral).

Refer to Figure 24

4.

Rotate cylinder lock channels down and forward off
transport lift cylinders.

Refer to Figure 25

5.

Rotate cylinder lock channel up and forward off front
box lift cylinder.

6.

Slowly reverse the lift circuit lever and begin lowering
the drill. Keep the circuit engaged until all three
cylinders are completely retracted. Set circuit to off
or neutral.

The drill is now ready for unfolding.

Figure 24

Transport Lift Cylinder Lock

18960

Figure 25

Front Box Lift Cylinder Lock

18959

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands