manualshive.com logo in svg

GREAT PLAINS 3S-4000, Operator'S Manual

Share
Download
GREAT PLAINS 3S-4000 Operator'S Manual Download Page 26

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Preparation and Setup

22

Hydraulic Hose Hookup

High Pressure Fluid Hazard:

Only trained personnel should work on system hydraulics!
Check all hydraulic lines and fittings before applying pressure.
Relieve pressure before disconnecting hydraulic lines. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Fluid escaping from a very small hole
can be almost invisible. Use paper or cardboard, NOT BODY
PARTS, to check for leaks. Escaping fluid under pressure can
have sufficient pressure to penetrate the skin causing serious
injury. If hydraulic fluid is injected into the skin or eyes, seek
immediate medical assistance from a physician familiar with
this type of injury. Within a few hours gangrene can start to
develop. DO NOT DELAY.

Color Coded Hose Handles

Refer to Figure 10

Great Plains hydraulic hoses now have color coded
handle grips to help you hookup hoses to your tractor
outlets. Hoses that go to the same remote valve are
marked with the same color. 

To distinguish hoses on the same hydraulic circuit, refer
to the symbol molded into the handle grip. Hoses with an
extended-cylinder symbol feed cylinder base ends.
Hoses with a retracted-cylinder symbol feed cylinder rod
ends.

1.

Connect opener-lift hoses to circuit designated for
hydraulic-motor control.

2.

Connect transport-lift hoses to tractor remote valve.

3.

Connect fold hoses to tractor remote valve.

4.

Connect marker hoses to tractor remote valve.

Check Drill Level

These items are set and verified at the factory or by your
dealer, but need to be checked prior to first use.

•

“

Center Box Frame Leveling

” on page 81

•

“

Opener Frames

” on page 81

•

“

Wing Box Alignment

” on page 82

•

“

Align Transfer Drive Shaft

” on page 83

•

“

Truss Tube Tension

” on page 85

•

“

Tool Bar Height

” on page 85

•

“

Opener-Frame Clearance

” on page 86

Color

Hydraulic Function

Red

Opener Lift Cylinders

Blue

Transport Lift Cylinders

Gray

Fold Cylinders

Green

Marker Cylinders

FigureSpacer

To run drill on tractors with open-center hydraulics or on
tractors with fixed-displacement hydraulic pumps, you must
install a Great Plains kit, part number 194-143A. If you are
not familiar with your tractor hydraulics, consult your tractor
dealer.

If your tractor has only two remote valves, you must
install a double-selector valve to combine the
transport-lift and opener-lift circuits. See “

Two Outlet

Hydraulic Kit

” on page 100.

Figure 10

Color Coded Hose Grips

31733

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands