manualshive.com logo in svg

GREAT PLAINS 3S-4000, Operator'S Manual

Share
Download
GREAT PLAINS 3S-4000 Operator'S Manual Download Page 11

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Important Safety Information

7

2018-06-19

Table of Contents

Index

195-442M

Safety Decals

Safety Reflectors and Decals

Your drill comes equipped with all lights, safety reflectors
and decals in place. They were designed to help you
safely operate your drill. 

Read and follow decal directions.

Keep lights in operating condition.

Keep all safety decals clean and legible.

Replace all damaged or missing decals. Order new decals
from your Great Plains dealer. Refer to this section for
proper decal placement.

When ordering new parts or components, also request
corresponding safety decals. 

Slow Moving Vehicle Reflector, Decal

818-003C

Center of rear center section;
1 total

Slow Moving Vehicle Reflector, Galvanized
Backing

818-055C

Mounted on bracket center of center section walk board;
1 total

To install new decals:

1.

Clean the area on which the decal is to be placed.

2.

Peel backing from decal. Press firmly on surface,
being careful not to cause air bubbles under decal.

18832

68421A

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands