manualshive.com logo in svg

Gravely 994149, Operator'S Manual

Share
Download
Gravely 994149 Operator'S Manual Download Page 28

EN - 26

Replace Relay

NOTICE: 

Relays are interchangeable. Use 

only quality replacement parts. See 

Service 

Parts

 on page 20.

See Figure 27.
1. Remove defective relay.
2. Determine cause of relay failure and 

repair condition.

3. Install new relay.

ADJUST TRANSAXLES

Check for Excessive Creep

1. Operate unit for a minimum of 5 minutes 

to warm hydraulic system.

2. Stop engine and engage parking brake.
3. Chock front wheels and support unit so 

both drive wheels are off the ground.

4. Remove drive wheels.
5. Start engine, move throttle lever to fast 

position and release parking brake.

6. Move steering levers forward and 

backward 5 or 6 times and then return 
levers to neutral position.

7. Check wheel hubs for rotation.

• If there is only slight rotation, stop 

engine, reinstall wheels and lower unit 
to ground.

• If there is excessive rotation, adjust 

neutral position. See 

Adjust Neutral 

Position

 on page 26.

Adjust Neutral Position

If wheel hub has excessive rotation after 
checking for excessive creep, adjust neutral 
position.
1. Loosen the return to neutral screw on 

transaxle. See Figure 28.

2. Slowly turn transaxle control arm in the 

opposite direction of hub rotation until hub 
stops. See Figure 29.

WARNING: 

AVOID INJURY. 

This adjustment requires 

operating the engine. Use 

extreme care to avoid contact 

with moving parts and hot 

surfaces. Be sure rear of unit is 

well supported and secure 

before starting engine.

START/RUN

RELAY

STARTER

SOLENOID

RELAY

PTO

RELAY

OPERATOR

PRESENCE

AUX

5AMP

CHARGING

20AMP

PTO

10AMP

CONTROLS

10AMP

TIME DELAY RELAY

07700221

TIME DELAY

10AMP

2

1

Figure 27

1. Relays
2. Fuses

Figure 28

1

Figure 29

2

1. Return To Neutral Screw
2. Transaxle Control Arm

Axle Direction

Summary of Contents for 994149













































Reviews:

No comments

Brands by name

Popular brands

Load more brands