GRAUPNER HoTT MC-16 Series, Programming Manual

Page: 94 / 332

94 Program description - Base setup models | Helicopter models
This option is available as standard on
both transmitter types.
Before programming specific parameters,
there are some basic settings to be made
which effect the currently active model memory.
Use the

selection keys on the left or right four-
way button to select the »Base setup model« option
in the multi-function menu:
Helicopter type
Suppress models
Base setup model
Servo adjustment
Control adjust
Stick mode
Open this menu option with a tap on the center SET
key of the four-way button pad:
Model name
Mod.name
Stick mode
module
1
n/a
Base setup model
n/a
DSC Output PPM10
HoTT
Change to the next screen page with a brief tap on
the
SET key of the right four-way button. This will
open a screen of characters for entry of the model’s
name. A maximum of 9 characters can be used to
specify a model name.
! " # $ % & ’ ( ) � + , – . / 0 1 2 3
4 5 6 7 8 9 : ;
Mod Name STAR
L
F G H I J K L M N O P Q R S T U V W X
Y Z [ ¥ ] ^ _ ` a b c d e f g h i j k
? @ A B C D E
Now the desired characters can be selected with the
selection keys of the left four-way button. Move to the
next position to select the next character with a tap on
the center
SET key of the right four-way button.
A simultaneous tap on the

or

keys of the
right four-way button (CLEAR) will place a space
character at the current position.
Positioning to any character position within the entry
field can be done with the

keys of the right four-
way button.
A return to the previous menu screen is accomplished
with a tap on the center
ESC key of the left four-way
button.
A model name entered in this manner will appear in
the base screen of the »Model select« menu and in
the sub-menus of the »Copy / Erase« menu item.
Stick mode
MODE 2 (Throttle at left stick)
pitch axis
pitch axis
tail rotor
tail rotor
throttle/pitch
throttle/pitch
roll
roll
throttle/pitch
throttle/pitch
tail rotor
tail rotor
pitch axis
pitch axis
roll
roll
pitch axis
pitch axis
roll
roll
throttle/pitch
throttle/pitch
tail rotor
tail rotor
throttle/pitch
throttle/pitch
roll
roll
pitch axis
pitch axis
tail rotor
tail rotor
MODE 1 (Throttle at right stick)
MODE 3 (Throttle at right stick) MODE 4 (Throttle at left stick)
Basically there are four different ways to assign the
four helicopter control functions, roll, nick, tail rotor
and throttle/pitch to the two sticks. Just which of these
is used depends on the preferences of the individual
model pilot.
Use the

selection keys of the left or right four-
way button to select the “Stick mode” line. The option
field will be framed.
Mod.name
Stick mode
module
1
n/a
Base setup model
n/a
SEL
DSC Output PPM10
HoTT
STARLET
Tap on the SET key. The currently displayed stick
mode will be displayed in inverse video. Now use the
selection keys of the right four-way button to select
from among options 1 through 4.
A simultaneous tap on the

or

keys of the
right four-way button (CLEAR) will reset the display to
stick mode “1”.
Another tap on the
SET key will again deactivate
option selection so a change to another line can be
affected.
Module
The
mc-16
HoTT and
mc-20
HoTT are fitted as
standard with a HoTT RF module. However, it is also
possible to switch to a non-Graupner|SJ external RF
module by software, if such a module is connected
to the transmitter. This is accomplished by using the
Select buttons of the left or right-hand four-way button
to move to the left, to the “Module select” value field:
1
n/a bind
BD1
STARLET
BD2
Rcv Ch Map R12 n/a
HoTT
Mod.name
Stick mode
module
Base setup model
HoTT
Graupner/SJ HoTT receivers must be “instructed” to
communicate exclusively with a certain model (mem-
ory) in a Graupner/SJ HoTT transmitter. This proce-
dure is known as “binding” and must only be done
once for every new receiver/model-memory-location
Base setup model
Model-specific base settings for helicopter models
mc
 
16 20