manualshive.com logo in svg

GRASS VALLEY Profile XP PVS1000, Installation Manual, Page: 43 / 46

Share
Download
GRASS VALLEY Profile XP PVS1000 Installation Manual Download Page 43

Select an RS-422 control protocol

23 February 2004

PVS 2000 Installation Guide

43

Setting up RS-422 remote control using Prolink (Profile protocol)

Use this procedure to start and set up Prolink to control the Profile XP Media Platform 
using Profile protocol.

1. Close VdrPanel if you used it earlier to test your record and play channels.

2. Open Prolink using the shortcut on the desktop or by selecting 

Start | Programs | 

Profile Applications | Prolink

. 

3. Select an RS-422 serial port, then click 

Select

. The Prolink window appears.

4. Test the PVS3000 system using your controller.

5. Repeat steps 2-4 for the number of control ports you need to control the PVS3000 

using Profile protocol. 

NOTE: For more information on the Prolink user interface see Chapter 8, 
“Controlling the Profile XP Remotely” in the Profile XP System Guide.

This completes all the procedures in this Installation Guide. Refer to the Profile XP 
System Guide for more information on customizing settings for your application.

Summary of Contents for Profile XP PVS1000















































Reviews:

No comments