background image

Operating the Menu System

Operator's Manual - LDK 5000

6-5

Security Menu for Owner's Access

The Security menu provides restricted access to special set-

up and security features of the camera.

Access to this menu requires the owner's unique smart card

for the camera or the PIN code that has been set for the

camera.

Note: An owner card is linked to the serial number of the

camera and is unique to that camera. It cannot be

used as an owner card for another camera.

Inserting the owner card into the camera gives direct access

to the security menu. If you select the Security menu without

this card inserted, you must enter the correct PIN code to gain

access to the Security menu.

User Levels

The installed user level function in the Security menu  restricts

access, in varying degrees, to the operational controls of the

camera. There are four user levels: user0, user1, user2 and

user3.

The purpose of the user levels is to restrict the set of functions

which can be changed by whoever is using the camera. In this

way a more centralized and uniform control can be achieved

and the danger of the camera operator accidentally changing

critical functions while shooting is reduced.

User level 0 is a special protection level which locks most of

the operational controls of the camera. Use this level to

ensure that a camera that has been set-up is not tampered

with. User level 0 is not normally used for operational purposes.

The appendix indicates which functions are available at each

user level.

Run Hours

This sub-menu allows the date and time to be set and allows

the running time of the camera to be viewed for the last 30

days.

PIN Code

The PIN code of the camera can be viewed and changed in

the Security menu.

The camera's PIN code when it leaves the factory is set to

0000. It is strongly advised that this code be changed by the

owner on receipt of the camera. This ensures added protection

against unaurthorised access to the Security menu.

Standard customer file

The green button on the side of the camera recalls the

standard scene file. This file contains standard parameters

for the picture performance.

A standard operator's file can be recalled via the Files menu.

This file contains parameters for the set-up of the camera.

A customer standard file can be defined for the standard

scene file and for the standard operator's file.

The contents of the customer files for both these standard

files is stored via the security menu. The selection of a factory

defined or a customer defined file for use as a standard file is

also made in this menu.

Summary of Contents for LDK 5000





































































Reviews: