GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 80 / 346

The Managed Network Interfaces dialog box allows you to edit and save changes to the device.

Modifying K2 client unassigned (unmanaged) interface

Prerequisites for this task are as follows:

•

The system description has a SAN K2 client that is a placeholder device.

•

The placeholder device has a one or more unmanaged network interfaces.

Use this task to modify unmanaged network interfaces on a K2 SAN device as follows:

•

K2 Summit Production Client

1. In the

Network Configuration | Devices

tree view, select a SAN K2 client placeholder device.

The interfaces for that device are displayed in the interfaces list view.

K2 SAN Installation and Service Manual

2014 01 27

Planning and implementing a K2 SAN with SiteConfig

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands