GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 272 / 346

background image

2. Shut down all K2 clients and all generic clients. You can do this via SiteConfig.

3. Take all K2 Media Servers out of service.

If you have redundant servers, make sure that you know which server is the current primary and
which server is the current backup, and that you take primary/backup servers out of service in
the proper order.

Related Topics

Taking a K2 Media Server out of service

on page 277

Bringing a K2 SAN online

1. Verify that RAID storage devices, Ethernet switches, and other supporting system are powered

up. Refer to the section earlier in this manual for power on procedures.

2. If K2 Media Servers are powered down, power them up. Refer to the section earlier in this manual

for power on procedures.

3. Place K2 Media servers in service.

If you have redundant servers, make sure that you place primary/backup servers in service in the
proper order.

4. Power on all K2 clients and all generic clients.

Related Topics

Placing a K2 Media Server in service

on page 279

Viewing iSCSI assignments

You can review a report of clients and their iSCSI configuration on a K2 SAN as follows:

1. In the K2Config application tree view, select the name of the K2 SAN, which is the top node of

the storage system tree.

2. Click

iSCSI Assignments

.

The iSCSI Port Assignments report opens.

The report displays the following information.

•

K2 Media Servers with the role of iSCSI bridge

•

Each server’s iSCSI ports, identified by IP address

•

For each iSCSI port, the iSCSI clients assigned and their bandwidth subscription.

Using reference files

When you create a simple K2 clip on a K2 system, K2 software can create a corresponding reference
file. The reference file is stored in a directory in the clip's folder on the V: drive. You can configure
the software to create QuickTime reference files or no reference files. The following topics provide
information about reference files on K2 systems.

272

K2 SAN Installation and Service Manual

2014 01 27

Administering and maintaining the K2 SAN

«
...
270
271
272
273
274
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: Qlogic Pages: 20

Brand: Gardebruk Pages: 32

HIMALAYA 100.S/2/CC

Brand: garofalo Pages: 12

Brand: HOMCOM Pages: 33

Brand: SanDisk Pages: 7

Brand: JetStor Pages: 71

Brand: Quantum Pages: 3

Brand: DEC Pages: 94

Brand: Mercia Garden Products Pages: 9

Brand: Eneo Pages: 12

Brand: IBM Pages: 228

Brand: Yardmaster Pages: 24

Brand: HOGYME Pages: 31

Brand: Craftsman Pages: 6

Tool Storage Roll-Away

Brand: Craftsman Pages: 4

HEAVY DUTY TOOL CHESTS

Brand: Craftsman Pages: 8

Brand: Craftsman Pages: 16

Munchen 63379505

Brand: Profiwerk Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands