GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 120 / 346

background image

The exact QOS values for your K2 SAN are calculated by Grass Valley to meet your workflow
requirements. When you operate your K2 SAN within the bounds of those requirements you should
have no bandwidth problems, even during peak bandwidth events. If your workflow requirements
change, allow Grass Valley to re-calculate your QOS values. Some versions of K2 software have a
RVIO calculator in the K2Config application. Do not use the RVIO calculator to change your RVIO
value. The calculator is intended for use by qualified Grass Valley personnel only. Do not attempt
to change any QOS values without guidance from Grass Valley. Doing so can result in unexpected
performance problems.

Importing a SiteConfig system description into K2Config

You can import a SiteConfig system description that contains a K2 SAN into the K2Config
application. You should do this only after the K2 SAN is fully complete and implemented in
SiteConfig, as changes are not automatically synchronized between SiteConfig and K2Config after
the import.

When you import a SiteConfig system description, K2Config identifies your SAN devices, defines
the SAN, and displays the unconfigured SAN in the tree view. Therefore you do not need to define
the K2 SAN in K2Config. You can skip this task and instead begin your work in K2Config by
configuring the first K2 Media Server.

1. In the K2Config application, click

File | Import SiteConfig

.

2. Browse to and select the system configuration file.

A K2 System Information dialog box opens.

3. In the drop-down list, select the type of K2 SAN that you are importing.

4. If a redundant K2 SAN, select “…

failover capabilities

…”

5. Click

OK

.

6. The SAN appears in the K2Config application.

Configuring the basic K2 SAN - Online and Production

Work through the topics in this section sequentially to configure an Online (Tier 1) or Production
(Tier 2) basic, non-redundant K2 SAN.

120

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

«
...
118
119
120
121
122
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: ECKELMANN Pages: 134

DiamondMax 17 160 ATA

Brand: Maxtor Pages: 64

Brand: Suncast Pages: 8

totalstorage 200

Brand: IBM Pages: 152

Brand: US Robotics Pages: 156

Brand: IBM Pages: 82

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Brand: LaCie Pages: 67

Brand: U.S. General Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 268

Brand: Salsbury Industries Pages: 5

Brand: OWIM Pages: 13

Brand: OWC Pages: 8

Brand: Mcombo Pages: 11

Brand: Clarke Pages: 8

Brand: LaCie Pages: 27

Brand: ramia Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands