GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 237 | Manualshive

Page: 237 / 366

background image

6. Verify or enter an IP address for the “B” media (iSCSI) network. Also enter the subnet mask.

7. Click

Next

.

The Database Client Configuration page opens.

Configure Database Client Configuration page - K2 client

This page connects the SAN client as a media database client to the K2 Media Server taking the
role of metadata (database) server. If there are redundant K2 Media Servers, both are listed on this
page as database servers.

1. Verify that the K2 client is connecting to the correct K2 Media Server or Servers, as follows:

•

For a basic (non-redundant) K2 SAN, the client connects to the only server.

•

For a redundant K2 SAN, the client connects to server A as database server 1 and server B
as database server 2.

If there are multiple FTP servers (such as the optional NH servers), the K2Config application
automatically assigns the SAN client to an FTP server to provide optimum FTP bandwidth across
the system. Do not attempt to change the assignment to a different FTP server while you are
doing this initial configuration.

2. Click

Check

.

3. When the wizard reports that the configuration check is successful, click

Next

.

The File System Client Configuration page opens.

02 February 2012

K2 SAN Installation and Service Manual

237

Configuring clients on the K2 SAN

«
...
235
236
237
238
239
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

CQDFX972U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 4

CQC1300U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 3

Brand: Coleman Pages: 12

Brand: Williams AV Pages: 2

EdgeVis HD-IP200

Brand: Digital Barriers Pages: 34

Brand: NSM Pages: 24

Brand: Delta Pages: 1

Brand: Nuova Marea Pages: 9

Brand: Tyba Pages: 14

Brand: BZB Gear Pages: 22

Brand: Barco Pages: 2

Brand: HQ Pages: 126

Brand: Aurora Design Pages: 2

Brand: LVS Pages: 8

Brand: Fischer Panda Pages: 94

Brand: Stanley Pages: 36

Brand: Calibre UK Pages: 37

Brand: Gentherm Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands