GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 233

Page: 233 / 366

9. After restart, to verify that the software is installed, on the Windows desktop right-click

Computer

and select

Manage

The Computer Management window opens.

10. In the left pane select

Device Manager

11. In the right pane open the

System devices

node and verify that

GVG ISCSI Multi-Path Device

Specific Module

is listed.

Configuring a K2 client for the K2 Storage System

Before doing this task, make sure the write filter is disabled on the K2 Summit system you are
adding to the K2 SAN.

1. On the PC that hosts K2Config, open the K2Config application.

A login dialog box opens.

2. Log in to the K2Config application with the administrator account.

The K2Config application opens.

02 February 2012

K2 SAN Installation and Service Manual

233

Configuring clients on the K2 SAN

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands

GRASS VALLEY K2 BASECAMP EXPRESS, Installation And Service Manual

Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands