manualshive.com logo in svg

GRASS VALLEY K2 BASECAMP EXPRESS, Installation And Service Manual

"Upgrade Instructions and user manual for the GRASS VALLEY K2 BASECAMP EXPRESS are now available for free download at our website. Discover step-by-step guidance and essential information to enhance your product experience. Simply visit manualshive.com to access these valuable resources and optimize the functionality of your K2 BASECAMP EXPRESS."

Share
Download
background image

5. Enter the control network IP address and other network settings.

6. For SNMP Configuration, enter the IP address of the NetCentral server PC.

You can also enter IP addresses for other SNMP managers to which you want to send SNMP
trap messages.

7. For the RAID chassis with two controllers, in the Controller Slot Number field enter 

1

 and then

press 

Enter

.

The settings from controller 1 are loaded into the Controller Network Settings dialog box and
are available for you to modify.

8. Repeat the previous steps to configure controller 1.

9. Click 

OK

 to save settings and close.

10. In Storage Utility click 

View | Refresh

.

Next, bind disk modules.

Binding disk modules - Nearline K2 SAN

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

Prerequisites for the optional K2 RAID Expansion chassis (if present) are as follows:

•

Fibre channel cable(s) connected

•

Power on

NOTE:  Binding destroys all user data on the disks.

1. If you have not already done so, launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

216

K2 SAN Installation and Service Manual 

02 February 2012

Configuring and licensing the K2 SAN

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Caliber MCD893 Operating Instructions Manual preview
MCD893
Brand: Caliber Pages: 26
Velux KSX 100 Service Instructions Manual preview
KSX 100
Brand: Velux Pages: 10
Thinkpower S3600TL User Manual preview
S3600TL
Brand: Thinkpower Pages: 30
ATEN VS132A User Manual preview
VS132A
Brand: ATEN Pages: 2
Niko 16-660-02 Manual preview
16-660-02
Brand: Niko Pages: 8
Triotech XBMC Clearstream Quick Start Manual preview
XBMC Clearstream
Brand: Triotech Pages: 16
Tektronix TSG 601 Instructions preview
TSG 601
Brand: Tektronix Pages: 2
Azbil MagneW Plus+ MGG14C User Manual preview
MagneW Plus+ MGG14C
Brand: Azbil Pages: 110
SIIG USB 2.0 Video Capture Device Quick Installation Manual preview
USB 2.0 Video Capture Device
Brand: SIIG Pages: 12
Enercell 22-135 User Manual preview
22-135
Brand: Enercell Pages: 12
IFM RM8004 Device Manual preview
RM8004
Brand: IFM Pages: 35
Radyne ComStream TIERNAN SE4000 Installation And Operation Manual preview
TIERNAN SE4000
Brand: Radyne ComStream Pages: 161
NAIM UnitiQute 2 Quick Start Manual preview
UnitiQute 2
Brand: NAIM Pages: 43
JS Automation JDAM-9530 User Manual preview
JDAM-9530
Brand: JS Automation Pages: 8
Xtender XTS 900-12 User Manual preview
XTS 900-12
Brand: Xtender Pages: 56
Vela CineCast 2000-0422 Installation And User Manual preview
CineCast 2000-0422
Brand: Vela Pages: 196
Salicru EQUINOX BATT EQX2 BATT User Manual preview
EQUINOX BATT EQX2 BATT
Brand: Salicru Pages: 40
V-TAC SUN-5K-SG04LP3-EU User Manual preview
SUN-5K-SG04LP3-EU
Brand: V-TAC Pages: 51

Brands by name

Popular brands

Load more brands